Bedienungsanleitung Thermocet Trimline Quadro 46 (Seite 23 von 34) (Englisch)

532670

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

Pag.23

11. INSTALLING THE UNIT (first read “General instructions”)

Please note: Before placing the unit, we recommend you first read Chapter 7

“Concentric flue system” on page 11.

11.1 Connection to the gas pipes (see page 24 for details)

You can determine where the gas pipes will be placed, dependent on the layout. Ensure control equipment is not

twisted during installation and there is no excessive tension. Accessibility of various connection points in relation to

components need to be maintained. After installation, check the connections for tightness in relation to gas. Use a

1/2“ gas tap with connection. Ensure the gas pipes are dirt-free and sand-free, and gas and combustion prod-

ucts from various parts and functioning is correct. The gas connection should only be undertaken when the elec-

tricity supply is disconnected. This prevents any damage occurring to the gas control equipment.

11.2 Preparation and installation of the unit

 Remove the packaging and check the unit for possible damage.

 Place the unit at the installation location

 Please note: place the unit on a stable surface.

 Please note: Do not place the unit on its back or on its side!

 The front window should now be removed in order to take the additional parts out of the unit.

 Remove the decoration strip (See Page 27-A) after this loosen the 2 “Z” profiles (See Page 27-B) at the top

and bottom by loosen the 4 screws (leave profiles).

 With the supplied suction cup you can remove the windows easily. Place the suction cup on the windows and

move it Carefully upwards, then Carefully and slowly pull the bottom of the window towards you. Next,

lower the window and leave it in a safe place where it cannot be broken or damaged.

Please note: the window is very fragile. You should therefore be very careful when (re) installing the

Window.

 Next, take the packed components out of the unit and check to make sure they are not damaged or broken.

installation situation

 Situate the unit (see page 28 as an example situation) in your chosen installation location . At the rear and the

sides, the unit must have at least 25 mm clearance from fireproof built-in materials. Install the supplied con-

vection grilles at least 50 cm below the ceiling on the appropriate wall. A lowered ceiling inside the whole

structure could be a possible solution in the event of a situation with a visual obstruction. For an assembly

with masonry, a lintel (see page 28-A) should be placed. It is also possible to build the fireplace using fire-

proof plate (See Page 28 fig.3)

 The legs of the unit can be adjusted, and if necessary shortened, see also dimensional drawings. The adjustable

feet allow fine adjustments (levelling) to be made.

 Gas pipe, thermocouple and ignition cables have been placed in coils under the unit. Cut the binders and

CAREFULLY unroll the various lines and cables to the position where the gas control cassette is to be

placed.

 Fixing to the wall is effected by means of adjustable wall brackets at the backside of the unit. Fastening mate-

rials are not included.

 Now determine the installation and assembly of the CC ducts and accessories. Please refer to Chapter 7.

”CONCENTRIC FLUE SYSTEM CC” on Page 10 and “Table of concentric pathways “ on Page 26.

 Build the control unit (B) to the your chosen installation location.

Please note:

The distance between the gas cassette / control cabinet and the unit will be determined by the cable /

thermocouple / line lengths from the control cabinet to the pilot burner and main burner.

The max. distance is approximately 1000 mm. The pipes, cables and/or couplings etc. should only be

connected when the electricity supply is off.

11.3 Fitting the ceramic log inset (see page 32 to 33)

* After servicing care must be taken that the burner is properly placed back Attn injector. Incorrectly installed

ceramic wood blocks and glowing material may have a significant influence on the fire image and the

burning effect.

* Spread both sides of the burner on the grill the black worm-like grains in bag A.

* Fill the burner, as indicated by the worm-like particles from the bag B.

* Place the ceramic wood blocks in the correct order as shown on Pag. 32 and 33.

* Glowing embers can be placed here and there as decoration. See Page 33 for example

MAKE SURE THE PILOT LIGHT REMAINS UNOBSTRUCTED!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Trimline Quadro 46 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermocet Trimline Quadro 46

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info