Bedienungsanleitung Thermocet Trimline Quadro 46 (Seite 4 von 85) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch)

532670

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

Page.3

1.1 General instructions

* The gas fireplace must be installed, connected and inspected as a balanced flue fire by a qualified fitter,

according to national, regional, and local standards and regulations.

* The flue system and the terminals in the outer wall or roof face must also meet the requirements

outlined in the applicable standards and regulations.

* The temperature of the walls and shelves near the side and back of the unit may not be more

than 80°C higher than the temperature of the environment.

* The unit has been approved in combination with the THC CC Ø100 mm - Ø150 mm and

Ø130 mm - Ø200 mm , in accordance with European CE standards for gas fires, and may therefore

only be applied with this system.

* The product needs to be serviced and inspected by the fitter for local gas distribution as indicated on

the identification plate.

* The instructions are only applicable if the relevant country code is stated on the unit. If this is not the

case, the gas technical information for the relevant country needs to be consulted and modifications

discussed with the manufacturer.

* There will be air in the gas pipes when the unit is first used. The gas pipes therefore need to be purged first.

* Ignite the fire according to operating instructions and check whether the burner flame is uniform.

After the unit has been used for the first time, you should remove any deposits resulting from

Running/burning in the paint, using a glass cleaner for heaters.

Distance to flammable materials:

* With respect to the front, side and top of the unit, a distance of 1200 mm needs to be kept between

the unit and: curtains, floor covering, upholstery and fabrics, and/or other flammable material unless

stated other wise in these instructions.

Distance to non-flammable materials:

* The unit needs to be placed a minimum distance of 25 mm from the wall unless stated otherwise in

these instructions.

The installation should be performed only by an authorized gasfitter

NOTICE

1. INSTALLATION INSTRUCTIONS

WARNING

Gas fires become hot when they are in operation. After installing the appliance the glass surface

is considered active zone. The glass surface can become very hot.!

Attention! Accordingly, care should be taken, for example children and needy in the vicinity of

burning fires are banned. Gas fires must not be on or against flammable materials are placed

(curtains etc.). Never install the unit against or within a flammable wall!.

Construction material for fireplaces and mantles etc. or built-in situation, must be made of

non-combustible material. This also applies to floors and ceilings. Never use flammable

materials near the unit in compliance with the above requirements.

If in doubt, consult your dealer

NOTICE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Trimline Quadro 46 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermocet Trimline Quadro 46

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info