Bedienungsanleitung Thermor STEATITE PRO (Seite 13 von 78) (Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

771213

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

1.21

Do not dispose your water heater in the garbage, but hand

it to a place assigned for this purpose (collection point)

where it can be recycled.

1.22

The instruction book of this product is available by contacting the

after-sales service.

INSTALLATION

- Refer to the corresponding diagrams p.2 & 3 (see table on right):

- Make sure to keep free space of 300 mm below pipes for the

exchange of the heating element.

- For vertical installation of Ø 505 devices if the wall is not strong

enough, an optional ground support is available. Nevertheless, it

is mandatory to fix the unit to the wall with the top bracket to avoid

tipping.

- For horizontal installation, the water connection tubes must

always be in a vertical position below the device.

HYDRAULIC

CONNECTION

- It is necessary to clean the supply piping prior to the hydraulic connection. The connection to the hot water outlet is to be

carried out with a cast iron or steel sleeve or a dielectric connector, to avoid corrosion of the pipe (direct contact iron / copper).

The use of brass fittings is prohibited.

INSTALLATION PRESSURISED: See fig. ❼, ❽, ❾&❿, p.4. Always install a new safety device on the cold water pipe

of the water heater, which comply with the standards (EN 1487 in Europe), with a pressure of 0.7 or 0.9 MPa (7 or 9 bar)

according to the nominal pressure, with diameter 1/2" or 3/4" (Table p.2). If expansion down the mains is required, the

safety valve and/or pressure reducing valve must be 3 mts from the water heater.

INSTALLATION UNPRESSURISED: See fig.⓫&⓬, p.4. For the supply of a single point of use, the installation must be

carried out with an optional special mixer tap.

- During heating up, water dripping may occur at the valve, do not obstruct the dripping. The safety device if

supplied does not meet the criteria for installation on French territory (Mainland and Overseas territories), do not use it.

ELECTRICAL

CONNECTION

- Refer to the corresponding diagrams p.2 & 5 (See fig.

⓭, ⓮, ⓯, ⓰, ⓱,⓲,⓳,

⓴,

- The water heater can be connected and operated only on AC 230V or on AC 220-240V in accordance with the rating plate

of the appliance. Connect the heater with a rigid cable with conductors 2,5mm². Use a standardised channeling (rigid or

flexible conduit) until the calibrated housing cover.

- Directly connect devices with a cable or plug. In France, a product with plug is strictly prohibited and cannot be sold and

installed.

- Always connect the earth conductor of the cable to the earth ground wire or connect the earth conductor to the appropriate

terminal identified by the symbol . This connection is compulsory for safety reasons. The earth wire green - yellow must be

longer than those of phases. The installation must be equipped, upstream of the appliance, with a bipolar cut-out device

(minimum contact distance of 3 mm fuse, breaker switch). In the case where HYDRAULIC connexions are in insulated

material, electrical circuits shall be protected by a differential circuit breaker 30 mA adapted to local standards.

- Thermal circuit breaker: All products are equipped with a thermostat including a thermal circuit breaker with manual reset,

which cuts the power in case of overheating. In case the security trips A: Cut the power before any operation. B: remove the

plastic cover. C: Check the electrical connection. D: Reset security. In case of repetitive tripping, replace the thermostat.

Never bypass safety or regulation thermostat. Connect the power only on the sockets or thermostat input.

STARTING

- NEVER POWER THE WATER HEATER WITHOUT WATER: Models with an electric heating element will be certainly

damaged.

- Fill the tank completely. Before powering up, open the hot water taps, drain the pipes in order to empty the air.

- Check the tightness of the tubes and of the flange seal under the plastic cover. In case of leaking tighten moderately. Check

the operating of the hydraulic components and of the safety valve.

- Turn the power on. After 15 to 30 minutes, depending of the capacity of the device, the water should drip from the drain. This

is normal and due to the expansion of water. Check connection leaks and seal. During heating and according to the water

quality, hot water tanks can make a bubbling noise. This noise is normal and does not indicate any defect of the unit.

- The thermostat is factory set to stop at 65 ± 5°C. If you see a continuous release of steam or hot water from the drain

or when opening a faucet, turn off immediately the power to the water heater and call a professional.

MAINTENANCE

- Before removing the plastic cover, make sure the power is turned off to avoid any risk of injury or electric shock.

The domestic maintenance must be done by the user. Operate the safety device every month to prevent scaling and check

that it’s not blocked. Not executing this maintenance may cause damage and the loss of the warranty. Maintenance

by qualified personnel A: Scaling: Remove the scale deposited as mud. Do not scratch or hit the scale sticking to the walls

to avoid damage to the coating. Do not forget to change the seal and reassemble the appliance, check that there is no

leakage of water after the first heating. B: For devices with magnesium anode, change the magnesium anode every two

Diameter Vertical installation Horizontal

installation

Ø255

See fig. under❷& above❸

Ø338

See fig. under ❷& above❸ See fig.❻

Ø380

Ø433

See fig.❹&❺ See fig.❻

Ø505

See fig.❺

Thermor STEATITE PRO Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info