Bedienungsanleitung Thetford C-402C (Seite 6 von 29) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Schwedisch)

576934

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

14. Bars should be glued for rigidity (see diagram 11). Reposition the rear wall

and fix in position. The wall should be standing between 16 and 40 mm in

front of aperture.

15. Trim the cut (from the door aperture) to fit the door panel according to

template 4A or 4B (make sure you use the right template!). Make sure the

decoration lines are lined up with the wall (see diagram 12).

16. Fill the groove of the door outer with sealant. Position the panel in the door

outer (see diagram 13), and then push the door inner into the door outer.

17. Fill the groove of the frame outer to be placed in the opening with sealant

(see diagram 14), place the complete door against the outside wall of the

vehicle and fasten the door with 9 sheet-metal screws (4.2x12.5mm).

18. Mount the frame inner from the inside onto the door (see diagram 15).

19. If the kicking plate was removed before installation, then reassemble it, fix it

with clips (3x) to the front bottom of the toilet.

20. In case of using wall brackets, fix these brackets to the rear wall using screws

(see diagram 16).

21. Install the shower tray first in case of new designed or adjusted shower tray.

22. Before positioning the toilet, the electrical connection has to be made first.

C-402 Red wire is the positive wire

Black wire is the negative wire

If the toilet is going to be connected to a pressure system:

C-403 Red wire is the positive wire

Black wire is the negative wire Drawing 1A

Purple wire is not required - do not connect

Grey wire is not required - do not connect

If the toilet is going to be connected to a non-pressure system:

Red wire is the positive wire

Black wire is the negative wire Drawing 1B

Purple wire is positive input (12V DC) - connect to electric supply

Grey wire is positive output - connect to positive side of pump

Remark: connect the negative wire to a common negative

23. Position the toilet against rear wall and aperture wall (see diagram 17).

24. Before installing the toilet, the C-403 has to be connected to the water supply

system. Connect the water hose of the cassette (inside diameter 3/8” =

10mm) to the water hose of the water supply with a hose adapter. Fix the

hoses to the adapter with a clamp (see diagram 1 8).

25. If using wall brackets, place the toilet over these brackets (see diagram 19).

26. Position the unit (through the door aperture from the outside) to the outside

wall, by gripping it at the pockets in the base. Secure the back panel of the

toilet to the bathroom rear wall with 4 screws (4 x 30mm) underneath the

toilet seat.

27. Install a cover strip if necessary (see diagram 20).

28. Add a run of transparent sealing mastic from the outside between door and

toilet (see diagram 21). The toilet is now installed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thetford C-402C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thetford C-402C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info