A. The refrigerator can be powered by the mains (230V), direct current (12V) or
liquid gas. Select the energy source that you want by means of the energy
source selector switch (A). The switch has four settings:
- direct current (DC) (12V)
- mains supply (230V)
- gas
- switched
B. The thermostat controls the refrigerator temperature when the refrigerator is
powered from the mains (230 V) or gas. The refrigeration level is indicated by
the dots (the bigger the dot, the colder the setting).
C. The flame meter shows whether the flame is alight. The flame is alight when the
red needle of the meter moves into the green area.
D. Pressing the manual (piezoelectric) starter produces a spark that ignites the
flame in the burner
4.1.1 Electrical operation
The refrigerator can be powered by electricity in two ways:
- DC (12V): Set the energy source selector switch (A) to
the refrigerator will now be powered by the battery of your car or camper
Important! - Always use the gas connection or mains voltage to start up the
refrigerator for the first time and to cool it. Powering from the battery of your
vehicle is suitable only for maintaining the temperature of the refrigerator and its
contents once it has been refrigerated.
- When powered by a vehicle battery (12 V) the refrigerator works without
temperature control (i.e. constant operation).
- Mains voltage (230 V): set the power selector switch (A) to
- Set the temperature by means of the thermostat, rotary switch (B). (The bigger
the dot, the colder the setting).
4.1.2 Powering with gas
Warning! - Flammable material must be kept away from the refrigerator
- For selection of gas type, see the information plate inside your refrigerator
- For the pressure regulator model, see the information plate inside your
refrigerator and the table at the end of this booklet.
- The type of gas container and its location must be in compliance with the most
recent regulations. Ensure that the unit is installed in a location with good
ventilation and make sure that the ventilation openings in the gas container
storage location remain open.
- The changing of the gas container must be done outside in the open air and out
of reach of any possible sources of ignition.
- Y
driving. If a road accident results in fire, there is a danger of explosion.
- Y
of petrol stations.
1 Open the valve of the gas bottle and the gas taps.
2 Set the Thermostat (B) to the highest level (the biggest dot).
3 Set the energy source selector switch (A) to
4 Ignite the gas flame:
Manual ignition (N80P
- Press the thermostat (B), and keep it depressed.
- Press the button for manual ignition several times at intervals of between 1 and
UK
2 seconds.
- Release the thermostat when the indicator of the flame meter enters the green
area. If it does not enter the green area, repeat the previous step.
Warning! Never keep the thermostat depressed for longer than 30 seconds. If a
flame does not appear
observe this rule, there may be an accumulation of gas creating the risk of fire or
explosion.
- Set the desired refrigeration level by means of the thermostat (B). (The bigger
the dot, the colder the setting)
Electrical ignition (N80E, N90E, N100E, N109, N110E, N145E):
- Press the thermostat (B) and keep it depressed.
- Ignition takes place automatically
successful, the noise will stop and the flame meter will turn green. Release the
thermostat.
- If the flame goes out, ignition will be repeated automatically.
- Set the desired refrigeration level by means of the thermostat (B). (The bigger
the dot, the colder the setting)
4.2 Switching off the refrigerator
- Set the energy source selector switch (A) to
- The refrigerator is now completely switched off.
- Use the special storage latch on the door locking mechanism to stop the door
from closing. This prevents unpleasant odours and mould in the refrigerator
Important! If you are not going to use the refrigerator for a prolonged period, close
the valve of the gas bottle and the gas taps.
5 SWITCHING ON THE REFRIGERA
panel according illustration 7)
- It is recommendable to clean the inside of the refrigerator before you switch on
the refrigerator
- Let the refrigerator run for at least eight hours before you place food in it for the
first time.
5.1 Smart Energy Selection (SES)
When you start up a refrigerator equipped with Smart Energy Selection (SES) you
should usually select the AUTO mode. The SES system will then automatically
select the best of the three available energy sources.
The system will apply the following priority:
- mains voltage (230 V)
- direct current (12 V)
- liquid
If an energy source becomes available that has a higher priority than the sour
refrigerator is currently using (e.g. if your vehicle engine is started), the system will
stop using the current energy source and switch to the energy sour
higher priority
If a fault occurs in one or more of the possible energy sources, the system will not
generate an error message while an alternative energy source is still available. The
SES system switches over automatically
If none of the energy sources is available, the LED of the main switch will turn
from green to red and flash every second.
SES models additionally allow you to select the desired energy source manually
5.2 Switching on the refrigerator
Important! The memorting.
Consequently
last-selected setting.
ILLUSTRA
A = Main switch (on/off)
B = Mode selection switch
C = Cooling level switch
D = Display LED
1. Open the valve of the gas bottle.
2. Open the taps of the gas supply
3. Press main switch (A). The LED alongside the main switch will turn green.
4. Use the mode selection switch to select the “Auto” function or one of the power
supplies that you want. The LEDs will show the option you have selected.
5. Set the desired cooling level by means of the cooling level selection switch (C).
The LEDs will show the cooling level setting you have selected.
A. Use the main switch to switch the refrigerator on and off. The LED alongside the
main switch will turn green. The display LEDs show the most recent settings.
After 10 seconds the display LEDs will go out. The LED of the main switch
remains green.
B. Press the mode selector switch and the display LEDs will show the setting for 10
seconds. Successively pressing the mode selector switch takes you through the
menu in the following sequence: AUTO, manual DC (12 V), manual gas, manual
mains voltage (230 V) and back to AUTO. Select either the AUTO option or one
of the other power supplies that you want to use. The LEDs show the option you
have selected. If you select the AUTO option, the system will choose the most
suitable power supply and the AUTO LED and the LED of the power supply
chosen by the system will both light up. T
selector switch, the system will switch off the LEDs. They will go out.
C. Use the cooling level selector switch to control the temperature of the
refrigerator
the currently set temperature will light up. Every time you press the cooling level
selector switch you set the refrigerator one position cooler
coldest temperature, the system will start again at the warmest temperature
setting. T
will switch off the LEDs. They will go out.
5.3 Powering with electricity
Powering with electricity can be selected both by the Auto mode and manually
5.3.1 Auto mode
Mains voltage (230 V):
This energy source will be selected if the mains voltage is greater than 200 V
power supply requires a continuous current of 12 V to operate the electronic
control system.
Direct current (12V) :
The SES system will select 12 V powering only if a mains voltage (230 V) is
- 7 -
6071_BW.qxd 24-06-2005 14:58 Pagina 7
