Bedienungsanleitung Thetford SERIE 930 (Seite 12 von 13) (Englisch)

576926

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

In your own interest of safety, it is law that all gas appliances be installed by an approved

competent person who will undertake to work to safe and satisfactory standards. Failure to

install the appliance correctly could invalidate any warranty or liability claims and lead to

prosecution. This appliance shall be installed in accordance with the local and

national/European standards in force. Particular attention shall be given to the requirements

regarding ventilation. Read the instructions before installing or using this appliance.

VENTILATION

This appliance is suitable for installation into Holiday Homes, Touring Caravans and Boats. In all

cases the national standards with regard to ventilation for the particular vehicle into which the

appliance is to be installed must be adhered to.

The appliance MUST have a gas escape hole (min size 50mm Ø; max 70mm Ø; or shaped hole

of equivalent area – 1965 to 3850mm

) in the floor, directly beneath the appliance. The hole

MUST vent to the outside.

LOCATION OF APPLIANCE

This appliance maybe installed in a kitchen/kitchen diner but NOT in a room containing a bath or

a shower. LP gas appliances must not be fitted below ground level. e.g. in a basement.

POSITION

The performance of the appliance meets the requirements of the European Standard for

Domestic Cooking Appliances (EN30) which specifies a maximum allowable temperature rise of

the furniture into which the appliance is installed of 65

C above the ambient temperature. To

ensure compliance with the standard it is important the installation follows the dimensions as

shown in this manual.

A cutout should be prepared – see Figs. 3,4 & 5 for model and details. The location of the cutout

MUST comply with Fig. 2 after the hob is installed – ie a direct distance of 200mm must exist

between the edge of the burner and combustible material unless protected by a layer of non-

combustible material.

The appliance should be fixed in place using the supplied clamps – see Figs. 6, 7 & 8 for model

type and clamping method.

For models with a glass lid, the distance from the edge of the burner to the rear wall can be

reduced to 110mm.

All combustible materials such as curtains and shelves must be kept well clear of the appliance.

Any fitments such as a cupboard above the appliance must have a minimum clearance of

500mm between the fitment and the top of the pan support.

This appliance must be positioned free from draughts, which may affect the combustion, and in

a manner that will prevent the accumulation of unburnt gas. When in use ensure that air vents

are not inadvertently blocked or shut off.

We recommend the underside of the hob be shielded particularly if this area is to be used for

storage or the installation of another appliance. The shield should be fabricated from

non-combustible material, but if the enclosure is manufactured from combustible material there

should be a minimum distance of 120mm between the worktop (top face) and the shield.

THIS AIR SPACE MUST BE WELL VENTILATED

INSTALLATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thetford SERIE 930 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thetford SERIE 930

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info