Bedienungsanleitung Thomashilfen EASyS (Seite 15 von 72) (Alle Sprachen)

682715

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Adjustment options

Seat width

Loosen the hip guide screws (EASyS) / arm support screws (EASyS Modular) from the seat top surface with an Allen key (provided

with the user manual, 3mm metric hexagon wrench) and move the lateral elements accordingly. (Fig. 10) If the seat depth is adjusted

to the minimal position, the maximal adjustable seat width depends on the existing space between the lateral back rest upholsteries.

Seat depth

Loosen all Allen screws (same as the hip guide setting) on the seat surface, stand facing the seat towards you and pull out the seat

plate. (Fig. 11)

Tip: For easy adjustment of the seat depth grip the frontal edge of the seat with one hand and press against the bottom part of

the backrest (concentric) with the other hand.

The hip guides (EASyS) are adjustable in depth, as well. Loosen both screws, set the desired depth, and retighten the screws. (Fig. 12)

Arm support (EASyS Modular)

The arm supports are adjustable both in height and depth. Loosen both wing nuts, set the desired height and depth, and retighten

the nuts. (Fig. 13)

Back height

Remove the lateral backrest upholstery slightly from the seat. Loosen both knurled screws at the top of the lateral tubes. (Fig. 14) The

back plate can be adjusted without fixed increments. The maximum height is achieved when the locking pin clicks in audibly. Velcro

fasten the lateral backrest upholstery.

To reduce the height press down the locking pin underneath the right knurled screw and push the back plate down to the desired

height. (Fig. 15)

Back height step 2 (EASyS only)

In order to achieve the maximum back height loosen both knurled screws at the top crossbar and pull up the back plate. (Fig. 16)

Tip: The extended body guides offer additional protection to children who are primarily transported in a lying position.

Headrest (EASyS Modular only)

Insert the tube of the headrest into the receiver at the top of the headrest bracket and tighten the wing screw. (Fig. 17)

The headrest can be adjusted without fixed increments by loosening the knurled screws on the rear of the backrest. (Fig. 18) To adjust

the angle of the headrest, loosen the wing screws at the headrest bracket. (Fig. 19) In addition, the headrest can be adjusted in depth

by loosening the wing screw on top of the headrest bracket. (Fig. 20) The angle of the headrest surface is adjustable both vertically

and horizontally by loosening the screws of the ball joint. (Fig. 21) Make sure to retighten all screws when adjustments are completed.

Back angle adjustment

Loosen the clamping lever at the backrest and pull out the safety locking pin below the lever. (Fig. 22) Now the backrest can be

adjusted in the desired position. The seat unit automatically slides forwards on its rails, shifting its center of gravity to maintain stability

in all seat positions. (Fig. 23) Retighten the clamping lever once the position is selected.

To lock back recline based on preset angles: Loosen the clamping lever at the backrest and pull out the safety locking pin below

the lever. Now the backrest can be adjusted in the desired position. The seat unit automatically slides forwards on its rails, shifting

its center of gravity to maintain stability in all seat positions. (Fig. 23) Engage locking pin and ensure it slides into a factory supplied

locking hole. Retighten the clamping lever once the position is selected.

Hint: The seat units have a different number of holes for the safety locking pin at the backrest.

EASyS 1: 2 holes; EASyS 2: 4 holes; EASyS Modular 1: 1 hole; EASyS Modular 2: 2 holes

During transport of the rehab stroller in a vehicle, the safety locking pin has always be locked in the bottom hole (90° back angle)

The other holes can be used to adjust further commonly used back angles.

Lower leg length

Loosen the threaded pins to the side of the foot rest with the Allen key (width across flats 3mm). (Fig. 24) The foot rest can be adjusted

without fixed increments. Retighten the threaded pins when adjustments are completed.

Foot angle

Loosen the 4 screws on the right and left on the bottom of the foot rest, adjust the desired angle, and retighten the screws. (Fig. 25)

A 10mm metric box wrench or spanner is needed.

Knee angle

Set the knee angle by loosening the side wing nuts on both sides. (Fig. 26)

Tip: The foot rest can be flipped up to facilitate transfers

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomashilfen EASyS Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info