Bedienungsanleitung Thomashilfen tRide (Seite 18 von 112) (Alle Sprachen)

682707

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

Fitting the seat unit

The lever on the headrest frame serves on the one hand to separate the seat unit from the subframe and on the other to

adjust the seat tilt angle. Hold down the lever on the headrest frame of the seat unit (fig. 3).

Insert the seat unit into the mounting adapter on the chassis and ensure that the pins on the side of the seat unit engage

in the recesses designed for this purpose. Bring the seat into the upright position until you hear it securely click into place.

Then check that the seat is properly locked in-place by pulling forwards on it (fig. 4).

Removing the seat unit

The seat can be removed from the subframe without the use of tools. Hold down the lever on the headrest and tilt the

seat unit backwards. The seat unit can then be removed by lifting it diagonally backwards and upwards out of the

mounting adapter on the chassis. It is recommended that you first lock the foot brake in the on position.

Fitting the footrest

The footrest must be secured at the toggle joints. To do this, place the ratchet joints one above the other and secure with

the screws (lever the inside), the washers (lever the outside) and the wing nuts (lever the outside) (fig. 5).

Lateral backrest upholstery

Place the lateral backrest upholstery over the lateral tube and use Velcro to fasten the upholstery to the curved lateral

parts of the back section (fig. 6). Completely close the Velcro – including over the knurled screw. Also use Velcro to

secure it to the back section (fig. 7).

Locators for weather canopy

The tRide rehabilitation stroller is fitted with locators to fit a weather canopy as standard (fig. 8)

Seat upholstery

Use Velcro to secure the seat upholstery to the seat. The two lower Velcro straps should be secured around the footrest

tubes (fig. 9).

Footrest tube padding

Use Velcro to secure the footrest tube padding around both the left and right tubes beneath the toggle joints.

Mounting the belts

Pass the two upper belts depending on the size of the child to either both inner or both outer loops of the back upholstery

and attach them to the rear of the backrest with the cam buckles. (Fig. 10)

The two bottom belt ends can be attached with the cam buckles to either the back plate or to the side of the plastic

element. (Fig. 11-13) Guide the belts left and right next to the back upholstery to the corresponding cam

buckle and fix them.

Tip: The belt length can also be adjusted from the front. Pull the D-ring to shorten the belt.

Basket

Fasten the basket (with its opening to the rear) to the four crescent rings on the frame using the spring clips (fig. 14a+b).

The basket may remain attached when folding the tRide. (Maximum loading of the basket: 5 kg).

Parking brake function

Please remove the cable tie that locks the foot brake.

Lock: Place your foot on the brake bar and press downwards.

Release: Place your foot underneath the brake bar and slide it upwards.

CAUTION: The brake release force is higher than usual in order to provide improved braking performance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomashilfen tRide Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info