Bedienungsanleitung Thomson 19HU5253W (Seite 4 von 10) (Englisch)

559152

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

EN 4

Initial setup

Initial setup involves selecting all the settings required

to be able to search for and store all the analog and

digital channels you can receive.

Make sure that the television is switched on and

follow all the steps in turn specied hereafter.

Note: TV channels search retrieved only the analog

chanels could be caused by poor broadcasting

and therefore is not covered by manufacturer

warranty. Manufacturer cannot be held

responsible for lack or poor broadcasting in

some areas.

The rst time you switch the set on, the Initial setup

wizard opens, which guides you through the initial

setup process. (Refer to Figure 1.) Press OK to start

your initial setup.

1. Press ▲/▼ to select your language, then press

OK/► to enter the next step.

2. Press ▲/▼ to select your country, then press

OK/► to enter the next step.

Note: When select France, you will have to

enter the Password setting menu here

in order to set a password. Use the digit

buttons to enter a four-digit number for your

password. (0000 is too simple to be set as

your password.) Re-enter the same code

to conrm the password. After that, you will

enter the next step automatically. (In this

step, you can only press ◄ to return to the

previous step.)

3. Press ▲/▼ to select your tuner mode Air or

Cable.

- Select Air.

• Press OK/► to enter.

• Press ▲/▼ to select Scan, then press OK/► to

automatically start the search relating to initial

setup for all DVB-T digital and analog channels.

- Select Cable.

• Press OK/► to enter.

• Press ▲/▼ to select Scan, then press OK/►

to directly start your initial setup or enter below

step.

• Select Full if available to search for and store

all DVB-C digital and analog channels.

• You may select other advanced scan mode if

available (for example, Advanced or Quick),

then congure proper cable information as

described below. Use the digit buttons to

adjust the values of frequency, symbol rate

and network ID; use ◄/► to select certain

modulation mode.

• Press OK to start initial setup relating to all

DVB-C digital and analog channels.

Note: To prevent the channel setup process from

being interrupted, wait for the message

indicating that the setup is complete.

4. Before start the scanning, you can also select Skip

scan to skip the initial setup progress.

5. During the setup, you can follow the hints available

at the bottom of the screen to return to the previous

step by pressing ◄. Or press Exit to exit or

interrupt the search halfway.

6. Once the automatic search ends, the set enters

the next step automatically. You can press ▲/▼ to

select your location Shop or Home. Press OK/► to

conrm your selection and enter the last step.

7. - In this step, you can press OK to exit the initial

setup. The channels are arranged in a preset

order. If you wish to skip channels, modify the

preset order or rename channels, select

Setup > Organiser and press OK/► to enter.

- In this step, you can also press ◄ to return to the

previous step.

Automatically install channels

This section describes how to search and store

channels automatically. Instructions are for both

analog and digital channels.

1. Press Menu on the remote control and select

Setup > Language > Menu language. Press

◄/► to select your desired menu language.

2. Press Menu to return to Setup, press ▲/▼ to

select Country, then press ◄/► to select your

country. The TV installs and arranges channels

according to your country.

3. Press ▲/▼ to select Tuner mode, then press

◄/► to select Air or Cable.

- Select Air.

• Press ▲/▼ to select Channel install, and

press OK/► to enter.

• Select Automatic search (Refer to Figure 2.),

then press OK/► to display Automatic search.

• Press OK to skip the country selection and

enter the next step. Or use ◄/► to reselect

your country, then press OK to enter.

• Select Digital & Analog, Digital or Analog,

then press OK/► to start the automatic search,

which relates to all DVB-T digital and/or analog

channels.

- Select Cable.

• Press ▲/▼ to select Channel install, and

press OK/► to enter.

• Select Automatic search, then press OK/► to

display Automatic search.

• Press OK to skip the country selection and

enter the next step. Or use ◄/► to reselect

your country, then press OK to enter.

• - Select Digital & Analog, then press OK/► to

enter. Select your scan mode if available and

congure proper cable information in the same

way as in Initial setup. Select Scan and press

Install channels

Chapter 2

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson 19HU5253W Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info