Bedienungsanleitung Thomson 24FW4323 (Seite 8 von 15) (Englisch)

559158

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

EN 8

Installing channels Chapter 3

Chapter 3 - Installing channels

Initial setup

Initial setup involves selecting all the settings required

to be able to search for and store all the analogue

and digital channels you can receive.

Make sure that the television is switched on and

follow all the steps in turn specied hereafter.

Note: If the channel search retrieved only the

analogue channels it could be caused by poor

broadcasting and therefore is not covered

by manufacturer warranty. Manufacturers

cannot be held responsible for lack of or poor

broadcasting in some areas.

The rst time you switch the set on, the Initial setup

wizard opens, which guides you through the initial

setup process. (Refer to Figure 1.)

1. Press

▲/▼

to select your language, then press

OK/► to enter the next step.

2. Press

▲/▼

to select your country, then press

OK/► to enter the next step.

Note: If you select France, you will have to

enter the Password setting menu here in

order to set a password. Use the numeric

buttons to enter a four-digit number for your

password. (0000 is too simple to be set as

your password.) Re-enter the same code

to confirm the password. After that, you will

enter the next step automatically. (In this

step, you can only press ◄ to return to the

previous step.)

3. Press

▲/▼

to select your tuner mode

Antenna or

Cable or Satellite. (Note:

Satellite option may not be available for certain

models.) Then follow a) or b) or c) below.

- a) If you have selected

Antenna.

• Press OK/► to enter.

• Press ▲/▼ to select Digital & Analogue or

Digital or Analogue, then press OK/►.

• Press

▲/▼

to select Scan, then press OK/►

to start the automatic search for all DVB-T

digital and/or analogue channels.

- b) If you have selected

Cable.

• Press OK/► to enter.

• Press ▲/▼ to select Digital & Analogue or

Digital or Analogue.

• If you select Digital & Analogue, press OK/►

to enter. Then:

- Press ▲/▼ to select Scan, then press

OK/►.

- Press ◄/► to select the scan mode if

available (Full or Advanced).

- If you select Full, press OK to start the

automatic search for all DVB-C digital and/or

analogue channels.

- If you select Advanced, use the numeric

buttons to adjust the values for frequency,

symbol rate, network ID, and use ◄/► to

select the modulation mode; then press OK

to start the search for all DVB-C digital and/

or analogue channels.

• If you select Digital, press OK/►to enter,

then follow all the same steps as for Digital

& Analogue above, to search for all DVB-C

digital channels.

• If you select Analogue, press OK/►to enter,

press▲/▼to select Scan, then press OK/► to

start the search for all analogue channels.

- c) If you have selected

Satellite.

• Press OK/► to enter.

• Press ▲/▼ to select one antenna type.

• Press OK/► to select one satellite, then press

OK to enter the next step to configure proper

information related to this satellite. Press OK

to go back after finishing settings.

• Press ► to start scanning.

Note: To prevent the channel setup process from

being interrupted, wait for the message

indicating that the setup is complete.

4. Before starting the scanning, you can also select

Skip scan to skip the initial setup process. In this

case, to search and store your channels you may

do an automatic channel search by following the

instructions in the next section Performing an

automatic channel search.

5. During the setup, you can follow the hints

available at the bottom of the screen to return to

the previous step by pressing ◄. Or press Exit to

exit or interrupt the search halfway.

6. Once the automatic search ends, the set enters

the next step automatically. Press

▲/▼

to select

your location Shop or Home. Press OK/► to

confirm your selection and enter the last step.

7. - In this step, you can press OK to exit the initial

setup. The channels are arranged in a preset

order. If you wish to skip channels, modify the

preset order or rename channels, select Setup >

Organiser and press OK/► to enter.

- In this step, you can also press ◄ to return to

the previous step.

Performing an automatic channel search

This section describes how to search and store

channels automatically. Instructions are for both

analogue and digital channels. This may be done in

any of the cases below :

- you have selected Skip scan in the Initial setup

- you see “Please scan channels!” in TV mode

- you want to update your channels.

1. Press Menu on the remote control and select

Setup > Language > Menu language. Press

◄/► to select your desired menu language.

2. Press Menu to return to Setup. Press ▲/▼ to

select Country, then press ◄/► to select your

country. The TV installs and arranges channels

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson 24FW4323 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info