Bedienungsanleitung Thomson 40FT8865 (Seite 15 von 17) (Englisch)

472023

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

English

• Set

Record

to check if you really want to start

your scheduled recording when the time you

have set comes. When time is out and you do

not execute any operation, scheduled recording

will start automatically.

Repeat type

: set different repeat modes for the

recording.

Press

▲/▼/

◄/► to select

Add

, then press

add the schedule you set into your schedule list.

Press the red button to repeat above procedures

to add another schedule.

If you wish to edit or delete a schedule, select it

and press

to enter.

Press

EXIT

to close the menu.

Network connection

You can set up your TV so that it can access the

Internet through your local area network (LAN) using

a wired or wireless connection.

Connecting to a wired network

You can attach your TV to your LAN using cable in

three ways:

• You can attach your TV to your LAN by connecting

the LAN port on your TV to an external modem

using a Cat 5 cable.

• You can attach your TV to your LAN by connecting

the LAN port on your TV to an IP Sharer, which is

connected to an external modem. Use Cat 5 cable

for the connection.

• Depending on how your network is congured,

you may be able to attach your TV to your LAN by

connecting the LAN port on your TV directly to a

network wall outlet using a Cat 5 cable. Note that

the wall outlet is attached to a modem or router

elsewhere in your house.

Select

Smart TV > Settings > Interface

, then select

Ethernet

to connect to a wired network.

Connecting to a wireless network

To connect your TV to your network wirelessly, you

need a wireless router or modem and a Wireless

LAN Adapter. Connect your Wireless High-Gain USB

Adapter (USB dongle) delivered with your TV to your

TV’s

USB 1

port.

Select

Smart TV > Settings > Interface

, then

select

Wireless

to connect to a wireless network.

Select

Wireless setting

and press

OK/

► to enter.

Connection Methods

: You can setup the wireless

network connection three ways.

Scan

• Select

Wireless setting

> Scan

, then press

OK/

►, the TV will scan all access points within

range. The access points found by the TV will

be displayed.

• Select an available access point, then press

OK/

► to connect the TV.

Notes:

- If you select a protected access point, you will

have to enter the corresponding password.

Press

on the remote control to display

the virtual keyboard to enable you to enter the

password.

- This set has a memory function of available

access point, which enables your set to be

connected to the network even if you switch

on the TV after power off.

Manual

Select

Wireless setting

> Manual

, then press

OK/

►, you will be prompted to enter the correct

SSID of an available wireless router to set up the

connection.

Auto

If your AP supports WPS (Wi-Fi Protected

Setup), you can connect to the network via PIN

(Personal Identication Number) or PBC (Push

Button Conguration). WPS will automatically

congure the SSID and WPA key in either mode.

Select

Wireless setting

> Auto

, then press

OK/

► to enter.

•

: Select

and press

OK/

► to enter.

Generate a random PIN code. Make sure

this code is installed on the AP. (For the

procedures, refer to your router manual.) Press

OK/

► again to set up the connection.

•

PBC

: If your router has a PBC push button,

select

PBC

, then press

OK/

► to enter. Press

the PBC push button on your router within 2

minutes after you press

OK/

► again. Your TV

will automatically acquire all the network setting

values it needs and connect to your network.

Network setup

Press

on the remote control and select

Smart TV > Settings > Internet connection

Press ◄/► to select

. Wait until the connection

is automatically established.

Select

Smart TV > Settings > Connection

test

, then press

OK/

► to check the Internet

connectivity. If it does not work, follow below steps

to make sure of the connectivity.

Select

Smart TV > Settings > IP setting

, then

press

OK/

► to enter the

IP setting

menu.

- Set

Address type

Auto

, it will acquire and

enter the needed IP address automatically.

- You can follow below steps to enter your IP

address manually.

• Set

Address type

Manual

, then press ▼ to

go to the rst entry eld.

• Enter the

IP address

Subnet mask

Default

gateway

Primary DNS

and

Secondary DNS

values. Use the alphanumeric buttons to enter

Network connection

Chapter 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson 40FT8865 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson 40FT8865

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info