Bedienungsanleitung Thomson 49UZ8766 (Seite 8 von 24) (Englisch)

582476

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

EN 8

English

Chapter 3 - Installing channels

Initial setup

Initial setup involves selecting all the settings required

to be able to search for and store all the analogue

and digital channels you can receive.

Make sure that the television is switched on and

follow all the steps in turn specied hereafter.

Note: If the channel search retrieved only the

analogue channels it could be caused by poor

broadcasting and therefore is not covered

by manufacturer warranty. Manufacturers

cannot be held responsible for lack of or poor

broadcasting in some areas.

The rst time you switch the set on, the Initial setup

wizard opens, which guides you through the initial

setup process. (Refer to Figure 1.)

Initialsetup

Please select your language:

Language

English

Български

Hrvatski

Čeština

Dansk

Select Next

Nederlands

Figure 1

1. Press ▲/▼ to select your language, then press

OK/► to enter the next step.

2. Press ▲/▼ to select your country, then press

OK/► to enter the next step. Press ▲/▼ to select

your location, then press OK/► to enter the next

step. Press ▲/▼ to select to continue or skip

network connection setup, then press OK/► to

enter the next step.

Note: If you select France or Italy, you will have

to enter the Password setting menu here

to set a password. Use the alphanumeric

buttons to enter a four-digit number for your

password. (0000 is too simple to be set as your

password.) Re-enter the same code to conrm

the password. After that, you will enter the next

step automatically. (In this step, you can only

press ◄ to return to the previous step.)

3. Press ▲/▼ to select your tuner mode

Antenna or

Cable or Satellite.

(Note:

Satellite option may not be available for

certain models.) Then follow a) or b) or c) below.

- a) If you have selected

Antenna.

• Press OK/► to enter.

• Press ▲/▼ to select Digital & Analogue or

Digital or Analogue, then press OK/►.

• Press ▲/▼ to select Scan, then press OK/►

to start the automatic search for all DVB-T

digital and/or analogue channels.

Note: not all countries have Favorite Network

Selection function.

- b) If you have selected

Cable.

• Press OK/► to enter.

• Press ▲/▼ to select Digital & Analogue or

Digital or Analogue.

• If you select Digital & Analogue, press OK/►

to enter. Then:

- Press ▲/▼ to select Scan, then press OK/►.

- Press ◄/► to select the scan mode if

available (Full or Advanced).

- If you select Full, press OK to start the

automatic search for all DVB-C digital and/or

analogue channels.

- If you select Advanced, use the numeric

buttons to adjust the values for frequency,

symbol rate, network ID, and use ◄/► to

select the modulation mode; then press OK

to start the search for all DVB-C digital and/or

analogue channels.

• If you select Digital, press OK/► to enter,

then follow all the same steps as for Digital

& Analogue above, to search for all DVB-C

digital channels.

• If you select Analogue, press OK/► to enter,

press ▲/▼ to select Scan, then press OK/► to

start the search for all analogue channels.

- c) If you have selected

Satellite.

• Press OK/► to enter.

• Press ▲/▼ to select one operator and press

OK/►.

• Press ▲/▼ to select one satellite, then press

OK to congure the proper information related

to this satellite. Press OK to go back after

nishing settings.

• Press ► to start scanning.

Note: To prevent the channel setup process from

being interrupted, wait for the message

indicating that the setup is complete.

4. Before starting the scanning, you can also select

Skip scan to skip the initial setup process. In this

case, to search and store your channels you may

do an automatic channel search by following the

instructions in the next section Performing an

automatic channel search.

5. During the setup, you can follow the hints available

at the bottom of the screen to return to the

previous step by pressing ◄. Or press EXIT to exit

or interrupt the search halfway.

6. In this step, you can press OK to exit the initial

setup. The channels are arranged in a preset

order. If you wish to skip channels, modify the

preset order or rename channels, select Setup >

Organiser and press OK/► to enter. In this step,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson 49UZ8766 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson 49UZ8766

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info