Bedienungsanleitung Thomson 49UZ8766 (Seite 18 von 24) (Englisch)

582476

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

EN 18

English

Chapter 6 - Network

High-Gain USB Adapter (USB dongle) delivered with

your TV to your TV’s USB 1 port.

1. Press MENU on the remote control and select

Network > Network settings > Internet

connection. Press ◄/► to select On.

2. Press ▲/▼ to select Interface, then set ◄/► to

Wireless to select wireless-mode connection.

3. Press ▲/▼ to select Wireless setting and press

OK/► to enter.

4. You can set up the wireless network connection in

3 ways: a) or b) or c).

- a) Scan

• Press ▲/▼ to select Scan, then press OK/►.

The TV will search all access points within

range, access points found by the TV will be

displayed.

• Press ▲/▼ to select an available access point,

then press OK/► to connect the TV.

Notes:

- If you select a protected access point, you will

have to enter the corresponding password.

Press OK on the remote control to display the

virtual keyboard to enable you to enter the

password.

- This set is able to memorize the available

access point, which enables it to connect to

the network even if you switch on your TV

after power-off.

- b) Manual

Press ▲/▼ to select Manual, then press OK/►,

you will be prompted to enter the correct SSID

of an available wireless router to set up the

connection.

- c) Auto

If your AP (Access Point) supports WPS (Wi-

Fi Protected Setup), you can connect to the

network via PIN (Personal Identication Number)

or PBC (Push Button Conguration). WPS will

automatically congure the SSID and WPA key

in either mode.

Press ▲/▼ to select Auto, then press OK/► to

enter.

• PIN: Select PIN and press OK/► to enter.

Choose a random PIN code. Make sure

this code is installed on the AP. (For the

procedures, refer to your router manual.) Press

OK/► again to set up the connection.

• PBC: If your router has a PBC push button,

select PBC, then press OK/► to enter. Press

the PBC push button on your router within

2 minutes after you press OK/► again. Your

TV will automatically acquire all the network

setting values it needs and connect to your

network.

Network connection

You can set up your TV so that it can access the

Internet through your local area network (LAN) using

a wired or wireless connection.

Connecting to a wired network

You can attach your TV to your LAN using cable in

three ways:

• You can attach your TV to your LAN by connecting

the LAN port on your TV to an external modem

using a Cat 5 cable.

• You can attach your TV to your LAN by connecting

the LAN port on your TV to an IP Sharer, which is

connected to an external modem. Use Cat 5 cable

for the connection.

• Depending on how your network is congured,

you may be able to attach your TV to your LAN by

connecting the LAN port on your TV directly to a

network wall outlet using a Cat 5 cable. Note that

the wall outlet is attached to a modem or router

elsewhere in your house.

1. Press MENU on the remote control and select

Network > Network settings > Internet

connection. Press ◄/► to select On.

2. Press ▲/▼ to select Interface, then set ◄/► to

Ethernet to select wired-mode connection.

3. Press ▲/▼ to select Connection test, then press

OK/► to check the Internet connectivity. If it does

not work, follow step 4 below.

4. Select Network > Network settings > IP setting,

then press OK/► to enter the IP setting menu.

You can set Address type to Auto or Manual.

- Select Auto if you want the TV to acquire and

enter the needed IP address automatically.

- Select Manual if you want to enter your IP

address manually, then:

• Press ▼ to go to the rst entry eld.

• Enter the IP address, Subnet mask, Default

gateway, Primary DNS and Secondary DNS

values. Use the alphanumeric buttons to enter

numbers and the arrow buttons to move from

one entry eld to another.

- Once Auto or Manual IP setting is completed,

press MENU to go back, press ▲/▼ to select

Connection test, then press OK/► to check the

Internet connectivity again.

5. If you want to see the information on current

connection, such as Interface, Address type,

IP address, etc., select Network > Network

settings > Information, then press OK/►.

Connecting to a wireless network

To connect your TV to your network wirelessly, you

need a wireless router or modem and a Wireless

LAN Adapter (some TV models are equipped with

an integrated LAN Adapter). Connect your Wireless

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson 49UZ8766 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson 49UZ8766

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info