Bedienungsanleitung Thomson ROC1407 (Seite 1 von 2) (Englisch)

607825

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

This universal remote control is compatible with most television sets controlled by infra-red.

This remote control was programmed in the factory, so that you can use it to control most of

the sets of the THOMSON group’s make. For this reason, we recommend that prior to

attempting to programme the remote control, you try it out by means of one of the methods

described in this user manual. However, first of all, you must install 2 batteries (AAA) in the

remote control.

Please keep this guide along with the code list (provided separately), so that you can

subsequently programme your remote control for use with other sets.

1 Indicator light: the red indicator light is lit whenever

a key is pressed.

2 On/Standby or Standby only, depending on the

equipment being used.

3 Activation and use of teletext (Videotext).

4 Selection of channels, input of digital values,

channels with 2 digits, external TV/VIDEO sources

(AV connectors).

5 Programming of the remote control.

6 Mute.

7 Zapping and volume control.

8 Activation and use of menus (display, deletion,

choice, confirmation).

9 Use of teletext (Fastext) or functions specific to

certain devices.

Note:

depending on the actual devices, manufacturers

and year of manufacture, the functions available will

vary.

The keys

Testing the remote control

before programming

Programming

the remote control

1. Switch on the set you want to control.

2. Direct the remote control towards the TV set and try

to switch it off by simply pressing the key

. If the

device does not turn off, you must program the

remote control using one of the methods A, B, C or

D described hereafter.

Method A – Fast programming

with 1-digit subcode

Method B – 4-digit codes

programming

Before you start programming, you must find the

subcode of the set to be controlled. Entering a sub-

code lets the remote control test a predefined list of

codes. Refer to the list provided with these instructions,

page I of the subcodes.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the red indicator

light blinks and then remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp flashes to signal that this time is almost up,

and then goes off).

3. While the indicator is lit

, type in the subcode

(example: 1 for THOMSON).

4. Direct the remote control towards the set and try to

switch it off by pressing the key

5. If the set you want to control switches off, press OK

to memorise the code.

6. Should the set not switch off, press key

repeatedly, until the set switches off. Between

pressing the keys, be sure to leave enough time for

the indicator light to go out and then relight (about

1 second). Proceeding this way will enable you to

see whether the set responds or not.

7. Immediately upon the switching-off of the set to be

controlled, press OK to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Before you start programming, you must find the code

of the set to be controlled.

Refer to the list provided with these instructions, page II

of the codes.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the red indicator

light blinks and then remains lit (the indicator light

remains on for a few seconds to give you the time

to proceed with the following steps. The indicator

lamp flashes to signal that this time is almost up,

and then goes off).

3. While the indicator is lit

, enter the first digit of the

4-digit code proposed for the set to be controlled

(example: 0036 for Thomson).

4. Direct the remote control towards the set and try to

switch it off by pressing the key

5. Should the set not switch off, repeat step 2. Then

type in the next 4-digit code. Try to switch off the set

by pressing key

once. Repeat this procedure by

trying out each of the 4-digit codes.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Method C – Programming by means

of code retrieval

Should none of the codes work, you still have the

possibility of retrieving the appropriate code without

having to perform any input.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the red indicator

light blinks and then remains lit.

3. Direct the remote control towards the set

and try to

switch it off by pressing the key

4. If the set you want to control switches off, press OK

to memorise the code.

5. Should the set not switch off, press key

as many

times as required (up to 200 times), until the set

switches off. Between pressing the keys, be sure to

leave enough time for the indicator light to go out

and then relight (about 1 second). Proceeding this

way will enable you to see whether the set responds

or not.

6. Immediately upon the switching-off of the set to be

controlled, press OK to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Try out other remote control keys to find out the range

of functions you can control. If you think that not all of

the keys are active, repeat the procedure of this

programming method to find out the code supporting a

wider range of features.

F01_GB_ROC1407 2/02/07 16:24 Page 1

Thomson ROC1407 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson ROC1407

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info