Bedienungsanleitung Thomson ROC2206 (Seite 1 von 3) (Englisch)

607826

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

The ROC 2206 is a universal remote control (2 in 1). It can replace 2 remote controls thanks to its

2 mode keys TV, VCR/DVD... It is compatible with the majority of television sets, video cassette

recorders, DVD players, satellite and cable receivers as well as terrestrial digital television (DVBT),

amplifiers and other audio equipment provided they are controlled by infra red signals.

This remote control has been factory programmed to allow you to use it immediately with the

majority of Thomson Group devices.We therefore advise you to try it before beginning to program it.

If programming is necessary, follow one of the methods A, B, C, D or E that are given in this manual.

But before anything else, fit the two batteries into the remote control handset and peel off the tab as

shown on the diagram on the inside of the cover.

Keep these instructions and the separate list of codes in a safe place so that you can later reprogram

your remote control.

1 I ndicator lamp: the indicator lamp lights up when any

key is pressed.

2 B: On / Standby.

3 R emote control mode

Selects device to control TV, DVD,VCR,...

4 S: programmes the remote control.

SHIFT: activates the secondary key features

(indications in blue).

5 I (EXIT): teletext Off in TV mode.

SHIFT and EXIT: turns off the menu of the

selected product.

6 c: switches the TV sound off.

SHIFT and OK: confirms a selection.

7 VOL-/VOL+ increases (+) or decreases (-) the

volume of the TV set.

SHIFT and VOL-/VOL+ also allows you to

navigate the menus horizontally.

8 M (RECORD): to record (VCR/DVD).

9 F (FF): fast forward *.

10 B (Play): play*.

1 1 K (Pause): stops on an image*.

1 2 Number keys 0 to 9: these keys have the same

functions as those of your original remote and are

also used to enter the codes fo

diff

ent pr

oducts

1 3 AV: for selecting an external source (SCART).

14 Press this key first before you type in the 2-digit

channel number (except for Thomson group

products).

1 5 L (STOP): stop playback*.

1 6 G (REW): goes backward or advances forward*.

17 "Info" key.

Videotext inlay on TV picture.

18 PROG+,PROG-: programmes zapping button

(received by the television set or the satellite

receiver); use to scroll vertically through menus

SHIFT and PROG+/PROG- also allow you to

navigate the menus vertically.

1 9 a (MENU): teletext On/Off in TV mode.

SHIFT and MENU: turns on the menu of the

selected products.

* The coloured buttons can be used to select categories

when teletext is activated, and specific functions

depending on the make.

2 - Te sting the remote control

before programming

1. T urn on the device that you wish to control.

2. P ress the key corresponding (3) to the type of device

to control:

TV: television set,

VCR/DVD: video cassette recorder, DVD player.

3. P oint the remote control at the device you wish to

control and try to turn it off using the

(2) key.

I f the device does not turn off, you must program the

remote control using one of the methods A, B, C or

D as described below.

1 - Description of keys

3 - Programming

the remote control

Before you start programming, you must find the subcode of

the set to be controlled.

Refer to the list provided with these instructions, page I of the

codes.

1 S witch on the set you want to control.

2. Hold down the S (4) key until the indicator lamp

(1) remains lit (the indicator light remains on for a

few seconds to give you the time to proceed with the

following steps. The indicator lamp flashes when this

time is almost up, and then goes off).

3. P ress the key (3) that corresponds to the type of

equipment you want to control:

TV: television set,

VCR/DVD: video cassette recorder, DVD player.

4. W hile the indicator is lit, type in the subcode (example:

1 for Thomson).

5. D irect the remote control towards the set and try to

switch it off by pressing the

(2) key.

6. I f the set you want to control switches off, press

c (6) to memorise the subcode.

7. If the product doesn’t turn off, press the

(2)

key repeatedly until the set switches off. Wait

approximately one second between key presses to

give the indicator lamp (1) enough time to go off

and light up again. This will allow you to see whether

the product responds or not.

8. I mmediately upon the switching-off of the set to be

controlled, press c (6) to store the subcode.

Note:

If you want to assign another type of product than those

mentioned on the remote control (with the exception of the

TV button which can only be used to control a television set),

begin by entering the code that corresponds to the product you

want to programme (a 4-digit code that you will find in the code

booklet – see method B).

Example: if you want to control a satellite receiver with the

VCR/DVD key, begin by entering a satellite code (any satellite,

for example: 0603 for a Thomson satellite receiver) then begin

the procedure.

Check of the programming:

In principle, your set is ready for receiving the remote control

commands. Check your remote control for proper functioning by

performing the test described on page 3.

Method A – Fast programming with

1-digit subcode

01_ROC2206_GB.indd 1 30/11/06 16:56:21

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson ROC2206 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson ROC2206

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info