Bedienungsanleitung Thomson ROC2406B (Seite 2 von 3) (Englisch)

607827

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

How to retrieve

a programmed code

Method C – Programming by means

of code retrieval

Method D - Automatic

code search

Should none of the codes work, you still have the

possibility of retrieving the appropriate code without

having to perform any input.

1. Switch on the set you want to control.

2. Hold down the S key until the key that corresponds

to the last mode you selected blinks and then

remains lit.

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set,

VCR/DVD: video recorder - DVD player.

4. Direct the remote control towards the set and try to

switch it off by pressing the key

5. If the set you want to control switches off, press

OK to memorise the subcode.

6. Should the set not switch off, press key

many times as required (up to 200 times), until

the set switches off. Between two key presses,

leave enough time for the key corresponding to

the selected mode enough time to light up again

(about 1 second). Proceeding this way will enable

you to see whether the set responds or not.

7. Immediately upon the switching-off of the set to be

controlled, press OK to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Try out other remote control keys to find out the range

of functions you can control. If you think that not all

of the keys are active, repeat the procedure of this

programming method to find out the code supporting a

wider range of features.

With this method, the remote control scrolls through

the full code list by sending an IR signal to the set to be

controlled remotely. Proceed as follows:

1. Check that your equipment is on. If not, switch it

on manually.

2. Hold down the S key until the key that corresponds

to the last mode you selected blinks and then

remains lit (the indicator light remains on for a few

seconds to give you the time to proceed with the

following steps. The indicator lamp flashes to signal

that this time is almost up, and then goes off).

3. Release the S key.

4. Press the key corresponding to the type of

equipment (for example TV).

5. Press the PROG

or standby

or PLAY

(VCR only) key. After a few seconds, the remote

control begins to scroll through the whole code

list included in the library (at a rate of roughly 1

code per second). Press the PROG

key once

again to slow down the test speed (1 code every

3 seconds). As soon as the set changes channels,

you must press OK to save the code and stop the

remote control scrolling through the list. If you do

not react quickly enough, you can go back to the

previous code by pressing PROG

or REW

(VCR only) as many times as necessary (you can

go forward by pressing

, PROG

or PLAY

(VCR only) if you have gone back too far). As

soon as the set responds again, press OK to save

the code.

It may be useful to retrieve the code programmed in

the remote control.

1. Hold down the S key until the key that corresponds

to the last mode you selected blinks and then

remains lit.

2. Press the key that corresponds to the type of

equipment you want to control:

TV: television set,

VCR/DVD: video recorder - DVD player.

3. Press the S key briefly, so that the last mode

selected blinks once.

4. Press the numbered keys in ascending order (0 to

9) until the selected mode blinks once.

5. The number that caused the selected mode to

blink is the first of the four numbers that make up

your code. Make a note of it below.

6. Repeat step 4 to find out the other numbers of the

code.

7. When the fourth number has been found, the

indicator light for the selected mode goes out.

6. Should the set not switch off, repeat step 2. Then

type in the next 4-digit code. Try to switch off the

set by pressing key

once. Repeat this procedure

by trying out each of the 4-digit codes.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Check of

the programming

- For a television set: turn on the set and press, for

example, 2 to change channels.

- Video recorder: load a tape and then press PLAY

(B).

- DVD player: load a DVD and then press PLAY (B).

Try other remote control keys to find out the range of

functions you can control. If you think that not all of

the keys are active, try the programming Method

B or C.

When you have retrieved the code of your

set, jot it down so that you can use it

whenever needed.

After battery replacement, you’ll have to

programme the remote control again.

Method E – Programming for control of

a COMBO (combined TV-VCR,TV/DVD,

VCR/DVD, … set)

Depending on the COMBO group (TV/VCR, VCR/

DVD, etc.) and the make, you will be required to enter

a single code for both devices in the COMBO, or to

enter two codes, one code per device. Consult the

separate list to discover this.

Before you start programming, you must find the

subcode or code of the subset to be controlled

(television or video recorder). Refer to the list supplied

with this user manual (see page subcodes or codes).

1. Switch on the COMBO you want to control.

2. Hold the S key down until the key corresponding to

the last selected mode blinks and then remains lit.

3. Press the key of the first device to control, and then

follow one of the programming methods A, B, C or

D previously described.

4. If a second code programming is required, then

repeat steps 2 and 3 above.

TV CODE

VCR CODE

DVD CODE

01_GB_Roc2406B.indd 2 20/12/06 10:15:27

Thomson ROC2406B Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson ROC2406B

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info