Bedienungsanleitung Thomson ROC3506 (Seite 6 von 60) (Deutsch, Englisch, Dänisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

699740

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

6.2 TV mode

Note

The remote control, in its factory conguration, is able to control approximately 90 per cent of all

TV sets for which it was designed. Generally,thereisnoneed to program settings. If the remote

control does not work, select one of the possible settings described in Section 6.2.

Manual input of the code for the TV set

• Press and hold the [FN] key and the [S] key at the same time for 3seconds until the

symbol

appears on the display (3).

• Release the [S] key,but keep the [FN] key held down.

• Enter the code for the TV set while continuing to hold down the [FN] key.The required code or

alternative codes can be found in the code list for TVs.

• Press the [S] key again until the

symbol disappears on the display.The entered code is now

saved.

• To leave the mode, press the [FN] and [S] keys again.

If only some of the essential functions (or none of them) can be controlled using the remote control,

you can enter an alternative code for your TV brand from the code list and then carry out the check.

Key function in TV mode

• Generally speaking, when the remote control is used to operate TVs (using infrared), only the blue-

highlighted keys areoperable

• The four coloured keys (red/green/yellow/blue) arelikewise intended for controlling TV-specic

functions (for example, videotext or settings).

• If you nd that some keys do not work, this may be because their function is not supported by

your specic TV version. Usually these functions can be subsequently programmed using the

remote control’slearning function (see following section).

Note

The remote control has some self-illuminating keys with aluminescent colour.For the keys to

illuminate in the dark, charging via an external light source is necessary.

Therefore, do not keep the remote control in dark places (for example, drawers).

Manual learning function

The learning function allows the functions of aremote control operating with infrared (IR)

transmission (referred to below as ‘RC A’)tobecopied to the Thomson universal remote control

(‘RCT’). This can help if the code list does not provide an appropriate code for your TV set model, or

if too few functions aresupported after code entry.

• Beforeperforming the learning function, make surethat the infrared transmitters of the device to

be copied (RC A) and of the Thomson remote control arefacing each other and no morethan 3

cm apart, and that the infrared sensors arepositioned so that they aredirectly opposite.

• Press and hold the (FN) and (L) keys on RC Tfor 3seconds until the „

“symbol appears on the

display.

• Press and hold the key that is to be programmed on RC T. Wait until the „ “symbol ashes on the

display and the Standby key is lit constantly.Please note that only the blue-highlighted keys

and the coloured keys areindividually programmable/have IR learning capability.

• On RC A, briey press the button to be copied. The „ “symbol no longer ashes, and the Standby

key LED ashes three times and goes out. Please ensureyou press the button only briey,to

prevent the learning of multiple IR commands.

Make sureyou continue to hold the key being taught on RC Tuntil this process has

nished!

• Now release the key with the learnt code on RC T.

• Press the „

“key on RC Ttostorethe programming process.

• To complete the learning mode, press the FN+L key again („ “goes out on the LCDdisplay).

• Then check whether the learnt function can be controlled on the TV set using RC T; if not, repeat

the procedure.

• Youcan now individually program afurther key in the same way.

Note

• Pre-programmed codes and keys with learnt codes willstill be retained.

• The learning function can be considerably impaired by strong light sources; you should

thereforeavoid performing this function in strong sunlight or LED light, or in the vicinity of

plasma TVs.

• The learnt functions will not be lost when you replace the batteries!

6.3 STB mode

Proceed in the mode for SET-TOP BOXES or DVB-T/DVB-C/DVB-Sreceivers (using infrared) as in TV

mode (6.2).

6.4 Audio mode

Proceed in the mode for audio devices (using infrared) as in TV mode (6.2).

TV/STB/audio keyboard functions

The scope of functions can vary depending on device and model.

Please note that the functions of the respective keys can likewise vary.

Note

• It may not be possible to offer additional functions that may exist on the device’soriginal

remote control.

• Furthermore, functions may be limited (depending on model). This does not mean that the

product is faulty.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson ROC3506 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info