Bedienungsanleitung Thomson ROC4411 (Seite 7 von 74) (Alle Sprachen)

699749

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

Check of

the programming

- For a television or a satellite receiver: switch on and,

for example, press 2 to change channels, etc...

- Video recorder: load a tape and then press B.

- DVD player: load a DVD and then press B.

Try other remote control keys to nd out the range of

functions you can control. If you think that not all of the

keys are active, try the programming Method B or C.

When you have retrieved the code of

Learning function

If the make of the device you wish to control is not in

the separate code list or if some functions are missing

in the code you have programmed, you can copy

the key functions of the original remote control of

the device into your ROC4411. Depending on the

format of the transmission codes of the original remote

control, your ROC4411 remote control can memorise

up to 150 keys.

Global delete – Delete all the keys copied

(this is recommended the rst time you use

this function)

1. Hold down the SETUP key until the indicator lamp

remains lit.

2. Release the SETUP key.

3. Press twice on the LEARN key. The indicator lamp

goes out and then relights.

4. Press once on the SETUP key. The indicator lamp

goes out after several seconds.

5. All the copied keys are now deleted.

Before starting

• The batteries in the 2 remote controls must be in

good condition; change them if necessary.

• First copy 2 or 3 keys from the original remote

control in order to check the compatibility of the

codes of both remote controls. Then carry out a

global delete of these keys before starting the full

learning procedure.

• Lay out the original remote control and your

ROC4411 end to end so as to align the LED

diodes on the 2 remote controls. Where necessary

adjust the height of both remote controls so that the

LED diodes are properly aligned.

• Place the remote controls with the infrared diodes

on a table so that they point each other at a

distance between 15 and 50 mm.

• Do not move the remote controls during the

learning procedure.

• Ensure that the room is not lit by uorescents tubes

or low consumption lamps since such light sources

can interfere with the copying.

• The 2 remote controls must be at least one metre

away from any light source.

• Avoid copying VOL and H keys codes and the

play keys since depending on the remote controls

the codes of these keys do not necessarily control

the same devices.

• When the memory of your ROC4411 is full,

the mode key will blink for 3 seconds. It is then

not possible to copy any more codes without rst

carrying out a global delete.

• When you copy a key, it is possible that the mode

key will blink feebly. In this case, do not release the

key and wait until the blinking stops.

Note 1: if the learning procedure does not seem to

work correctly, try the following:

1. End the learning procedure by pressing SETUP.

2. Check that the LEDs of the two remote controls

are properly aligned. Carry out the alignment

procedure.

Modify the distance between the remote controls, in-

creasing or reducing the distance from 1.5 cm to 5 cm.

Restart the procedure from the beginning.

5. If the problem persists and always with the same

key, check that the original remote control is

actually operating: is it sending IR signals? (check

batteries; is it correctly aligned in relation to the

diode on your ROC4411?)

Note 2:

• You cannot copy keys to the LEARN SETUP and

MODE keys.

• All the keys copied to a mode will be deleted if a 4

gure code is entered for this mode (and likewise

for direct entry of a code, search of a code or

make).

Identifying the position of the diode on the

original remote control (keys to copy)

If the Infrared LED of the original remote control is not

visible (for example, if hidden behind a dark plastic

plate), the instructions below will help you to locate

it precisely.

1. Place the front of the original remote control (the

part you point at the device to control) around

2.5 cm from the LED of your ROC4411 (see

LEARNING diagram above).

2. Hold down the SETUP key until the indicator lamp

remains lit.

3. Release the SETUP key.

4. Press once on a mode key (TV, DVD, …). The

indicator lamp goes out and then relights.

5. Press once on the LEARN key.

6. Hold down one of the keys on the original remote

control while moving the remote control from left

to right. As soon as the 2 remote controls are

correctly aligned, the indicator lamp blinks rapidly.

7. To copy the key functions from your original

remote control into your ROC4411, go to step 5

of “To copy keys”.

Note: Some original remote controls don’t transmit

continuous IR signals when a key is held down. If this is

the case, press several times on one of the keys while

moving the remote control from left to right.

To copy keys

1. Hold down the SETUP key until the indicator lamp

remains lit.

2. Release the SETUP key.

3. Press once on the mode key (TV, DVD, ...).The

indicator lamp goes out then relights.

4. Press the LEARN key once.

5. Press once on the key of your ROC4411 to which

you want to copy one of the keys of your original

remote control.

6. Hold down the key of the original remote control

you wish to copy until the indicator lamp goes

out and then relights (2 to 3 seconds). In case

of problems, the indicator lamp will blink for 3

seconds but will remain in learning mode. Try

again or try another key.

7. For the other keys, repeat the procedure from step

5 onwards.

8. Press the SETUP key once when all the desired

keys have been copied. The mode key goes off.

To delete all keys copied under a mode

1. Hold down the SETUP key until the indicator lamp

remains lit

2. Release the SETUP key.

3. Press once on a mode key (TV, DVD, SAT,...).

The indicator lamp goes out then relights.

4. Press twice on the LEARN. key. The indicator lamp

goes out then relights.

5. Press once on the SETUP key. The indicator lamp

goes out. All the keys copied under this mode are

deleted.

SAT/STB CODEAMP CODE

TV CODE

DVD CODE

your set, jot it down so that you can use it

whenever needed.

After battery replacement, you may have to

programme the remote control again.

Thomson ROC4411 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info