Bedienungsanleitung Thomson ROC8507 (Seite 8 von 48) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

607824

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Setting the timer

Used to program up to 4 timers. You may assign up to 4

keys to the Timer so that it will activate at the set time (for

example, to change the Mode SAT channel over to 123 at

22:35). The  rst key must always be a mode key. The

following keys may not include 5,6,4,3, OK EXIT,

MACRO, SETUP, or any other mode key. Timers may only

be set to be activated within the following 24 hour

period. Timers are automatically cleared after having

been activated. The Timer

“ ”

symbol is displayed when

a Timer is set.

1. T urn on the device in TV Mode.

2. U sing the SETUP keys, and navigation keys

5,6,4,3, OK display CODE SETUP then OPTION

SETUP then TIMER SETUP (press OK) then TV SLEEP

SETUP then TIMER X SETUP (X corresponds to one of

the 4 timers).

3. P ress OK once to display TIMER X SET.

Note: Clear the timer if it already contains a program (see

below).

4. U sing keys5,6, OK, select the desired start time

(hour and minutes), Press OK.

5. SELECT TIMER X MODE? is displayed. Using the

mode keys, indicate the device to be controlled (TV,

DVD, VCR).

6. T he indication SELECT TIMER X KEYY? is displayed.

Press once on the key that corresponds to the desired

command (e.g. 1).

7. T he indication SELECT KEY 2 is displayed. Press

once on the desired key (e.g. 3) or on OK if you do

only want to send one command, and go to Point 10,

below.

8. T he indication SELECT key 3 is displayed. Press once

on the desired key (e.g. 8).

9. T he display brie y indicates SUCCESS before

returning to CODE SETUP.

10. P ress EXIT to exit this mode.

11. S et the remote control down on a table or  at

surface at the level of the TV set’s infrared receiver

with its front end pointed toward the device to be

controlled.

Note: the symbol “ ” is displayed when a Timer is set.

Clearing a timer

1. U sing the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK display

CODE SETUP then OPTION SETUP then TIMER

SETUP (press OK) then TV SLEEP SETUP then

TIMER X SETUP (press OK) then TIMER X CLEAR.

2. P ress OK once to display TIMER X CLEAR.

3. P ress OK once to display CONFIRM OK TO CLEAR.

4. Press OK once.

5. T he display brie y indicates SUCCESS before

returning to CODE SETUP.

Key learning

This function is used to copy the functions of keys

on other remote controls to the keys on your ROC

8507 in the mode and to the keys of your choice.

Your ROC 8507 can store up to 150 keys (depending

on the format of the IR code to be learned). Only

one original remote control may be stored per Mode

(refer to the notes concerning learning). The remote

control may also be pre-programmed using one

of the codes in the library, and copied keys may

be «superimposed» on the key positions selected by

the user: The remote control can thus be customised

by the user, who uses a pre-programmed code, then learn

the key functions from his original IR remote control.

Careful: Yo u may not copy onto the Setup, Home Cinema or

Macro keys • All of the commands copied for one mode are

erased if an identical or new 4-digit code is entered for this

mode (also applies to direct entry of a code, a code search

or brand search) • The screen and key backlighting is o

during learning.

Advice before you begin:

• P lace the remote controls face to face so that the

IR LED diodes of the two remote controls are precisely

lined up. You may need to adjust the height of

the remote controls so that the LED diodes are

properly aligned. Verify that the gap between the

two remote controls is about 25 mm [1 inch]. Do not

change the gap between the two remote controls

during the learning of all the keys required for this

mode.

• B egin by copying 2 or 3 keys (to get used to it), then

perform the “Clear All Learn Modes“ function (clear

all learn modes) before learning the entire keyboard

of your original remote control.

How to copy (learn) keys

1. U sing the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate up to LEARN SETUP (press OK)

then LEARN ONE MODE (press OK) then SELECT A

MODE KEY.

2. P ress OK once.

P ress the desired mode key once (TV, DVD, VCR, etc.)

to display SELECT A MODE KEY TO LEARN

4. P ress once on the key of your ROC 8507 to which

you wish to copy the code of the original remote

control.

5. T he indication LEARNING: PLEASE WAIT appears.

6. W hile LEARNING: PLEASE WAIT is displayed, hold

down the key on the original remote control until

SUCCESS or KEY LEARN ERROR appears on the

display before releasing the key on the original

remote control (normally after 2-3 seconds).

7. T he indication OK – LEARN MORE or EXIT? is

displayed. To copy another key, press once on OK

then begin again starting with Step 5 or press EXIT

once to exit this mode.

8. T he display brie y indicates PLEASE WAIT before

leaving this mode.

Erasing the functions learned in a mode

Erases all the keys copied in a given mode

1. U sing the SETUP keys, (hold down for 7 seconds)

and navigation keys 5,6,4,3, OK, display CODE

SETUP then navigate up to LEARN SETUP (press OK)

then LEARN ONE MODE then CLEAR ONE LEARN

MODE.

2. P ress OK once to display SELECT A MODE KEY.

3. P ress the desired key (TV, DVD, VCR, etc.) once to

display CONFIRM OK TO CLEAR

4. P ress OK once.

5. T he display brie y indicates PLEASE WAIT before

leaving this mode.

Erasing functions learned for all modes

Erases all the keys copied (overall erasing is recommended

for the  rst learning)

1. U sing the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display

CODE SETUP then navigate up to LEARN SETUP

(press OK) then navigate up to CLEAR ALL LEARN

MODES.

2. P ress OK once to display CONFIRM OK TO CLEAR.

3. P ress OK once.

4. T he display brie y indicates PLEASE WAIT before

leaving this mode.

Automatic sleep setup for the TV set

Used to program the sleep setup for a TV set using the TV

Sleep Timer mode (“Zzz”).

1. T urn on the device in TV Mode.

2. U sing the SETUP keys (hold down for 7 seconds),

and navigation keys 5,6,4,3, OK, display

CODE SETUP then navigate up to TIMER SETUP

(press OK) then TV SLEEP SETUP (press OK) then

TV SLEEP SET.

3. P ress OK once.

4. U sing keys 5,6 and OK, select the number

of minutes (from 1 to 90 minutes) before the TV

enters sleep mode when TV SLEEP TIME? is

displayed.

5. T he display brie y indicates SUCCESS before

returning to CODE SETUP.

6. P ress EXIT twice to exit this mode.

Note: The “Zzz” symbol is displayed when a TV Sleep Timer

is set.

7. S et the remote control down on a table or  at surface

at the level of the TV set’s infrared receiver with its

front end pointed toward the TV set.

Note: to clear the programming, navigate up to TV SLEEP

SETUP then TV SLEEP CLEAR. Press OK once when CONFIRM

OK TO CLEAR is displayed. The display brie y indicates

SUCCESS before returning to CODE SETUP.

Thomson ROC8507 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info