Bedienungsanleitung Thomson THS 812 (Seite 12 von 27) (Englisch)

480544

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

QUICK GUIDE TO USING YOUR RECEIVER

English

4.3 Satellite Selection

This receiver is already adjusted for reception of Astra Satellites with the correct settings as it is

most common. Per default it is setup for DiSEqC port 1 for Astra 19.2 and DiSEqC port 2 for

Astra 23.5.

In case you are not connected to any switch or using a Mono block you can keep currently

settings.

To check or change the settings for the satellite on port 1 press OK to enter the submenu.

In case port 1 is already correctly adjusted and you have proper signal quality and strength

banners you can adjust the port 2 if you have a satellite connected there. Use

p/q to select it

and proceed like below chapter describes. This you can do for up to 4 Satellite positions.

4.3.1 Edit LNB

In this submenu you can adjust following parameters:

Satellite: Press OK to open the list of available satellites and chose the desired one

with

p/q or PG+/-.

LNB Type: Choose the desired LNB Type via the

t/u buttons if you are not using a

“Universal” LNB.

LNB Low Freq.: This shows the value for the appropriate LNB Type used and you can only

adjust for “Normal” LNB.

LNB High Freq.: This shows the value for the appropriate LNB Type used and you can only

adjust for “Normal” LNB.

22 KHz Tone: This setting for AUTO should not be changed, only in case it is necessary

for your LNB type.

LNB Power: Here you can change the LNB power via

t/u in case it is necessary.

Transponder: Press OK to open the list of available transponders for the chosen

satellite, in order to check your reception or align the antenna.

After all settings are adjusted following to your system requirements, choose Save with

p/q or

Cancel to discard changes and press OK. The receiver will return to the selection screen and

you can continue by pressing the BLUE Next button.

4.4 Scan Selection

In this menu you can use p/q to highlight the desired option and press OK to choose the

desired item from the list.

In Scan Mode you can choose Quick Scan which scan only transponders of selected country

and Full Scan to scan all transponders from selected satellite(s).

In NIT Search you can select ON if you want to scan for new appeared channels /

transponders or OFF if you don’t like to.

After everything is setup following to your preference, choose the BLUE Next button.

The receiver will perform the chosen scan process. Afterwards all found channels will be stored

and the receiver will switch to the ﬁrst found channel respectively the ﬁrst.

5.0 QUICK GUIDE TO USING YOUR RECEIVER

We at THOMSON understand that you can’t wait to enjoy your new HD receiver. The following

quick guide will make you familiar with the basic operation of this device. We do, however,

advice you to read the full manual to get the best performance from your THOMSON HD

receiver.

To turn your receiver ON or to Standby, use the q button on the remote control or the button

on the left side of the front panel.

Choose the desired channel with the

p/q buttons or the P+/P- buttons. Alternatively, you can

digit the channel number with the 0~9 buttons on the remote control or press OK in viewing

mode to display the channel list.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson THS 812 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info