Bedienungsanleitung Thomson THS 812 (Seite 15 von 27) (Englisch)

480544

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

P10

MAIN MENU

7.1 Installation

This menu allows you to change satellite settings and to search for channels. Further you can

adjust important settings for your receiver. It consists of the following sub-menus: Antenna

Setup, Channel Search, System Settings, Parental Lock and Factory Reset. Choose the

desired sub menu with

p/q and press OK to advance.

7.1.1 Antenna Setup

Use this menu to change or add the settings for an already installed or new satellite and to

conﬁgure its parameters. In the Type line you can adjust if you’re using a DiSEqC switch or not

by using

t/u to change. If your setup differs you can adjust DiSEqC OFF or use default setting

DiSEqC 1.0.

Is DiSEqC OFF used you will only be able to setup one satellite. Press OK to open the settings

for this connection.

For the usage with DiSEqC 1.0 you can enter the same parameters for up to 4 satellite positions.

Edit LNB

Satellite: Press OK to open the list of available satellites and chose the desired one

with

p/q or PG+/-.

LNB Type: Choose the desired LNB Type via the

t/u buttons if you are not using an

“Universal” LNB.

LNB Low Freq.: This shows the value for the appropriate LNB Type used and you can only

adjust for “Normal” LNB.

LNB High Freq.: This shows the value for the appropriate LNB Type used and you can only

adjust for “Normal” LNB.

22KHz Tone: This setting for AUTO should not be changed, only in case it is necessary

for your LNB type.

LNB Power: Here you can change the LNB power via

t/u in case it is necessary.

Transponder: Press OK to open the list of available transponders for the chosen

satellite, in order to check your reception or align the antenna.

After all settings are adjusted following to your system requirements, choose Save with

p/q or

Cancel to discard changes and press OK. The receiver will return to the selection screen and

you can continue.

In case you want to delete a desired satellite press the GREEN button. If you want to delete all

satellites that have been setup use the YELLOW button to do so. Once all settings are made,

press EXIT/SORTIE to change to the previous menu.

7.1.2 Channel Search

Use this menu to perform an automatic, network or transponder channel search or to search on

all satellites that have been setup. Use

p/q to highlight the desired item and t/u to change

settings. Below the settings you can ﬁnd the search methode selection.

Antenna: Here you can change the antenna port via

t/u in case you have

conﬁgured more than one satellite.

Satellite: Here you will see the according satellite which is assigned to the antenna

in above, you can only see the satellite(s) which has/have been setup in

Antenna Setup menu before.

Transponder list: By using

t/u you can change between the transponders referring to the

selected satellite, you can also press OK to list up and select with

p/q

or PG+/-. Afterwards press OK to choose. Use RED to Edit TP, with

GREEN you can Delete TP and with BLUE you can enter data for a new

TP Add TP.

Scan Mode: Here you can decide for which channels you want to scan: Either scan

all channels FTA & $, for Free-To Air only FTA or use CA to scan for

scrambled channels only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson THS 812 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info