699585
11
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
English
7
By connecting your receiver to the latest digital ampliers or home theatre systems with HDMI
connections, you will enjoy the best possible sound quality and multi-channel audio (depending on
broadcast), up to Dolby Digital Plus. Connect the HDMI output of the receiver to an input of your
amplier, and then connect the HDMI output of the amplier to your TV set. Select the correct input
on your amplier to watch and listen to programmes.
3.6 Connecting to Ethernet
Fig. 7
Connect a CAT5 cable (or higher quality) to the LAN (RJ45) connector of the unit and the other end
to an existing switch, router or modem. The default setting is Auto (DHCP) for automatically obtaining
IPs and DNS. Select DHCP O in Menu> System>Network Setting>IP setting to enter your own
settings if required. When setting up manually, you need to provide a unique IP address, Netmask,
Gateway and DNS for your receiver. Refer to the manual of your router or modem to setup properly.
signalling will give momentary status of connection, like cable unplugged, local network or internet.
3.7 Connecting a USB storage device
Fig. 8
NOTE: We recommend the use of a hard disk drive USB 2.0 or higher for
recording and play back of TV events.
For proper functioning of Timeshift and recording functions, a fast USB device (such as a hard
disk drive) is needed. Interrupted playback or a distorted picture during playback or Timeshift are
indications for a low device speed. STRONG cannot guarantee proper functioning of recording and or
Timeshift functions with all USB devices.
4.0 STARTING UP FOR THE FIRST TIME
If you use your receiver for the rst time, the Installation Guide menu appears. Use pq to move the
highlight to the setting you wish to change and use t u to change values. Start by selecting your
On-Screen Language (OSD) using t u. Once you have selected your language, press q to move
the highlight to Country. Select your country using t u.
Other options are:
Antenna Power: Set to On if you use an active antenna. When set to On, a 5 Volt power will
be present on the RF IN connector of the receiver. Select O for passive
antennas.
Scan mode: Select All to store scrambled and free to air channels or select FTA to store
only Free-To-Air channels. Note: Scrambled channels you cannot watch with
this receiver.
Once all settings are made, move the highlight to Channel Search and press OK to start scanning.
The receiver will now search for all available channels. Once scanning is nished, the receiver switches
to viewing mode.
NOTE: Selecting the wrong country may result in a disorderly channel list, and
missing of channels.
TIP: In case the Installation Guide menu does not appear after switching on
the receiver the rst time, reset the receiver to factory settings by pressing
the MENU button and selecting Restore Factory Default in submenu
System. (Default PIN 1234)
5.0 QUICK GUIDE TO USING YOUR RECEIVER
We at STRONG understand that you can't wait to enjoy your new high denition digital terrestrial
receiver. The following quick guide will make you familiar with the basic operation of this device. We
do, however, advice you to read the full manual to get the best performance from your receiver.
To turn your receiver ON or to Standby, use the q button on the remote control.
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Thomson THT709 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Thomson THT709

Thomson THT709 Bedienungsanleitung - Französisch - 23 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info