706696
14
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
- EN 5 -
Pairing the Device:
1. Place the speaker near the Bluetooth-enabled device and switch the speaker on.
2. Press and hold the Bluetooth button to put the speaker into pairing mode if it is not already in
search mode. The LED next to the Bluetooth logo will start ashing.
3. Go to the Bluetooth settings on your device.
4. Select the Bluetooth name “WS06IPB ”. If your device asks for a passcode enter ‘0000’
5. The Bluetooth LED remains fully lit when pairing is complete and a sound prompt conrms it is
paired.
6. The speaker will automatically pair to the last device it was paired to when it powers on again. If no
known device is found, it will enter pairing mode again.
Aux Function:
For other compatible music player devices, or MP3 players, please use the auxiliary audio line cable
(included) to connect from your external device’s “LINE OUT” jack to the “AUX-IN” jack of this speaker.
The speaker will beep when a cable is attached and the left side LED will slowly ash.
Receiving/rejecting Calls:
While in wireless mode, press the Call button to accept an incoming call.
Press the Call button again to end the call.
You can also recall the last used number by pressing this button.
You only can reject a call from your device and not from the speaker.
Please check below for the full LED light status indications.
Note that if the speaker is only operating on battery, the Blue \ Red LED will only display the blue
colour.
Working status Bluetooth LED Indicator
(Blue/Red)
Wireless charging LED
Indicator (Green/Red)
Power on Blue\ Red LED quickly
Flashing
Red LED constant
Bluetooth pairing mode Blue \ Red LED quickly
Flashing
No Change
Bluetooth connected
successfully
Blue LED constant No Change
Play music Blue \ Red LED slow Flashing No change
Pause Blue LED constant No change
Make call via Bluetooth Blue LED constant No change
AUX In Mode Blue \ Red LED light ash No change
USB charging for other
device
No change according to the
current state
No change
Use AC adaptor to charge
speaker
Red LED constant ,Blue LED
No change according to the
current state
No change
Speaker full charged Red LED off No change
Put the Phone on wireless
charging area
No change according to the
current state
Green LED constant
Phone full charging No change according to the
current state
Red LED constant
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Thomson WS06IPB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info