Bedienungsanleitung Toa M-864D (Seite 11 von 60) (Englisch)

692130

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

29. Front-mounted Stereo input 2 jack [ST 2 IN]

–10dB*,10kΩ,unbalancedtype,stereominijack.

It is internally connected in parallel to the Stereo

input 2. Adjust the input level with the Stereo 2

Input volume fader (28).

30. ARC switch and ARC operation indicator

[ARC] (Green)

Press this switch to enable the Automatic

Resonance Control function (ARC).

Hold down this switch for 3 seconds to start

the ARC measurement, and the ARC operation

indicatorashes.

Uponmeasurementcompletion,theARClteris

set, and the ARC indicator lights. (See p. 28.)

31. Recording output switch and Recording

output indicator [REC OUT] (Green)

The indicator lights when the switch is pressed,

and the Control knob (6) is allowed to adjust the

recording output volume. (See p. 25.)

* 0 dB = 0.775 V

[Rear terminal section]

32 33 34 35 36 3637

38 38

39 39

42 43 44

32. AC inlet

Connect this inlet to the AC wall outlet using the

supplied dedicated power cord.

33. Output terminals [OUTPUT 1 – 4]

+4dB*,600Ω,balancedtype,removableterminal

block.

The input channel signals assigned to Buses

1 through 4 using the Assignment switches (19

and 26) are output from each individual output

terminal.

Buses 1 through 4 correspond to the output

terminals 1 through 4, respectively.

34. Contact output terminals [OUTPUT C, 1, 2, 3,

4, 5, 6, 7, 8, C]

Removable terminal block, 8-channel contact

output terminal.

Perform function assignment to each contact by a

PC using the supplied M-864D PC Software.

35. Contact input terminals [INPUT C, 1, 2, 3, 4, 5,

6, 7, 8, C]

Removable terminal block, 8-channel contact

input terminals.

Perform function assignment to each contact by a

PC using the supplied M-864D PC Software.

36. AC adapter input [LINK A and LINK B]

Connect the dedicated AC adapter or its

equivalent* that supplies 24 V DC power to the

ZM Remote controller.

* Use the AD-246 AC adapter (optional) or its

equivalent. As for the usable adapter, consult

your TOA dealer.

37. Termination switch [TERMINATION ON, OFF]

UsedtoturnONorOFFtheterminationof120Ω

for parallel connection.

38. Data line connection terminals [D+, D–]

Connect the data line from the ZM Remote

controller to these terminals.

Match the polarity.

39. 24 V DC output terminals [DC 24 V, + and –]

Supply 24 V DC to the ZM Remote controller.

40. LAN port

Connect this port to the LAN-connected switching

hub using a LAN cable.

The MX-864D’s default IP address is “192.168.14.1.”

Perform settings by a PC using the supplied

M-864D PC Software.

• Link indicator

Lights when the link is established and during

data transmission or reception.

• Full indicator

Lights during Full duplex operation.

41. Functional ground terminal

Connect this terminal to the functional ground of

external equipment if much noise is encountered

when the digital audio processor is connected

to the external equipment. The noise may be

reduced

Note: This ground is not for protective ground.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toa M-864D Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info