Bedienungsanleitung Toa MM-700F (Seite 13 von 36) (Englisch)

692132

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

19. MUTE SENSE control (PRIORITY 1, PRIORITY 2)

Adjust the threshold (sensitivity) of the mute function of the PRIORITY 1, PRIORITY 2 inputs. In other

words, if PRIORITY 1, PRIORITY 2 input signal exceed the threshold that set by MUTE SENSE, it will

mute the LINE 1, LINE 2, LINE 3, LINE 4 signal to CH1, CH2, CH3, CH4 outputs. Rotate clockwise will

raise the sensitivity, counter-clockwise will lower the sensitivity.

20. HOLD TIME control (PRIORITY 1, PRIORITY 2)

Adjust the recovery time of the LINE 1, LINE 2, LINE 3, LINE 4 to CH1, CH2, CH3, CH4 outputs. Rotate

clockwise will increase the recovery time (maximum 10sec), counter-clockwise will decrease the

recovery time (minimum 50ms)

21. PRIORITY FUNCTIONAL DIP SWITCH (PRIORITY 1, PRIORITY 2)

Control the functionality of the PRIORITY 1 and PRIORITY 2

Switch No. ON OFF

1 PRIORITY 1/2 can be switched to CH1 output PRIORITY 1/2 cannot be switched to CH1 output

2 PRIORITY 1/2 can be switched to CH2 output PRIORITY 1/2 cannot be switched to CH2 output

3 PRIORITY 1/2 can be switched to CH3 output PRIORITY 1/2 cannot be switched to CH3 output

4 PRIORITY 1/2 can be switched to CH4 output PRIORITY 1/2 cannot be switched to CH4 output

5 The mute function is controlled by the PRIORITY

1/2 input signal or manual mute (16)

The mute function is only controlled by the

manual mute (16)

6 PRIORITY 1/2 input gain switch to MIC level PRIORITY 1/2 input gain switch to LINE level

22. PRIORITY MIX1+2 switch

Control the input mode of the PRIORITY 1/2

ON OFF

PRIORITY 1 and PRIORITY 2 will be mixed and output

to CH1, CH2, CH3, CH4 when mute activated. The

PRIORITY FUNCTIONAL DIP SWITCH (20), MUTE

SENSE control (18), HOLD TIME control (19) will be

followed by PRIORITY 1’s setting

The PRIORITY 1 has the higher priority level than

PRIORITY 2. When There is mute function activated.

Unit will output PRIORITY 1’s input first.

23. EQ BANKS and PRESETS SELECTION

The 2-bit DIP switch select the bank of respect to the 16 EQ presets. Total 4 banks.

The 4-bit rotary switch selects 16 EQ presets from each banks.

Note: The functionality of CH2, CH3, CH4 is the same as CH1.

Please see page 23, "11.2 EQ preset selections" for more details.

24. HPF SWITCH (*)

Control the activation of HPF (High Pass filter) on outputs.

ON OFF

The CH1, CH2, CH3, CH4 will has 50Hz, -12dB/oct. high

pass filter on output. This is useful to protect the speaker

when the transformer of the distribute speaker couldn’t

handle low frequency.

The output frequency response is flat from 20Hz to

20kHz.

25. REMOTE TERMINALS (CH1, CH2, CH3, CH4 remote controls)

RJ45 connector, use for connecting the remote module WP-700.

After connecting WP-700 could provide the following functionality:

1) Switch the input source LINE 1, LINE 2, LINE 3, LINE 4 to CH1, CH2, CH3, CH4 outputs.

2) Adjust the volume of connected channel.

Note: When the WP-700 is connected, the OUTPUT LEVEL CONTROL (3) on front panel and INPUT

SELECT SWITCH (10) won’t be functional. It means this two function will follow WP-700 setting. Also,

the REMOTE INDICATOR (8) will light.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toa MM-700F Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info