Bedienungsanleitung Toledo TEAG-115-500 (Seite 8 von 24) (Deutsch, Englisch)

485747

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Toledo

Disassembly

Remove the flange nut and the flange from •

the spindle (2).

Remove the machine’s protective hood.•

Assembly

Put the protective hood (1) on the machine.•

Turn the protective hood to the position •

indicated in the drawing and completely

tighten the screws (3).

Put the flange nut and the flange back on the •

spindle (2).

Mounting a grinding disc

Fig. C

Use grinding discs of the correct dimension. •

Use fibre reinforced grinding discs only. The

grinding disc must not touch the edge of the

guard.

Press the spindle lock and turn the spindle (9) •

until it engages in the lock. Keep the spindle

lock pressed during this procedure.

Remove the flange nut (12) from the spindle •

using the spanner (11).

Position the grinding disc (7) on the flange (5).•

Place the flange nut on the spindle an tighten •

it using the spanner.

Release the spindle lock and check that the •

spindle is unlocked by rotating it.

Mounting the side handle

Fig. A

The side handle can be used for both left-•

hand and right-hand control.

Fasten the side handle (Fig. A-3) for left-hand •

operation on the right-hand side of the

machine.

Fasten the side handle for right-hand •

operation on the left-hand side of the

machine.

Makesurethatthesidehandleis

fastenedproperlyandcannotloosen

unexpectedly.

4. USE

Alwaysobservethesafetyinstructions

andapplicableregulations.

Wearearandeyeprotection

Do not place the machine on the workpiece when

switching the machine on or off. The grinding disc

may damage the workpiece.

Clamp the workpiece and make sure that the •

workpiece cannot slide from under the

machine during the cutting activities.

Hold the machine firmly and press it under an •

angleofapproximately15˚againstthe

workpiece. Move the grinding disc evenly

across the workpiece.

Regularly inspect the grinding disc. Worn •

grinding discs have a negative effect on the

efficiency of the machine. Replace a grinding

disc on time.

Always switch off the machine first before •

removing the plug from the wall socket.

Switching on and off

This machine in equipped with a safety switch and

needs to be unlocked before operation.

Press at the bottom of the switch to unlock the •

on/off switch.

Slide the on/off switch forwards.•

To switch off, depress the on/off switch, this •

will then jump to the ‘off’ position.

Do not put the machine down when the motor •

is still running. Do not place the machine on a

dusty surface. Dust particles may enter the

mechanism.

Neverusethespindlelocktostopthe

motor.

Neverusethemachineforgrinding

magnesiumworkpieces.

5. SERVICE & MAINTENANCE

Makesurethatthemachineisnotlive

whencarryingoutmaintenanceworkon

themotor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toledo TEAG-115-500 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info