Bedienungsanleitung Tomado TGH6001W (Seite 21 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

761310

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

EN - 21



If the hob is connected according to the class 1 specifications, only flexible metal hose can be used which meet the valid

national regulations. Gas feeding connector must be G ½” threaded coupling. Use only pipes and fittings that

meet the requirements of the valid standards. Maximum admissible length of the flexible hose is 2000 mm. Make sure the

connection is not touching any mobile elements which could damage the hose.



The hob comes with a G ½” threaded coupling. The connection to gas supply must be done in a manner that excludes stresses

in any point of the pipework or parts of the appliance. Make sure you do not exceed the torque when making the connection

(maximum torque is 20 Nm). Otherwise, the connection may be faulty or leaks may occur.

The gas hose should not touch metal elements of the hob back shield.

 Each time you replace a reducer, carry out technical inspection of the hob that covers gas valves and proper

operation of the flame failure cut-off device.

 On completion of the hob installation, the tightness of all connections should be checked, e.g. applying water

with soap. Do not use fire to check tightness.

ELECTRICAL CONNECTION

ADAPTING THE HOB TO ANOTHER TYPE OF GAS

This operaon may only be carried out by an appropriately authorised er.

If the gas the hob is to be supplied with diers from the gas provided for the hob by the manufacturer, that is G25/ 25.3 / 25 mbar,

burner nozzles must be exchanged and the ame needs to be adjusted.

In order to adapt the hob to burn a dierent type of gas, you should:

• exchange the nozzles (see the gas tables below);

• adjust the “economical” ame.

The hobs provided by the manufacturer have burners which are factory-adapted to use the gas specified on their

rating labels.



G25/ 25.3-25 mbar* G20/20 mbar G30/30 mbar

SABAF burners

Injector

diameter Injector mark Injector

diameter Injector mark

1 0.72 mm 72 0.72 mm 72 0.50 mm 50 1 Simmer burner 0.95 kW

2 0.97 mm 97 0.97 mm 97 0.65 mm 65 2 Semi-rapid burners 1.70 kW

3 1.15 mm 115 1.15 mm 115 0.85 mm 85 1 Rapid burner 2.90 kW

Burner ame Re-arming from liquid gas to natural gas Re-arming from natural gas to liquid gas

Full 1. Exchange a burner nozzle for the appropriate type

according to the gas table.

1. Exchange a burner nozzle for the appropriate type

according to the gas table.

Economical 2. Unscrew an adjusng bolt slightly and adjust the ame size. 2. Screw in an adjusng bolt slightly and check the ame size.

In order to perfom adjusng operaons, take o the knobs.

• Check that the voltage in your home corresponds with the voltage printed on the boom of the appliance.

• The earthing of the appliance is compulsory by law.

•  the connecon point must always be accessible.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tomado TGH6001W Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info