Bedienungsanleitung TomTom Rider Pro (Seite 5 von 97) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

470679

Zoom out

Zoom in

Vorherige Seite

1/97

Nächste Seite

Using your TomTom Rider

Using

your

TomTom

Rider

Switching on

Press and hold the On/Off button for 2 seconds, or

until your TomTom Rider starts.

The first time you switch on your TomTom Rider, it

may take up to 20 seconds to start. To switch off

your TomTom Rider, press and hold the On/Off but-

ton for 2 seconds.

Before you use your Rider for the first time, it’s a

good idea to charge it fully.

The battery in your TomTom Rider navigation

device charges when you connect it to the home

charger or to your computer.

Note: You should plug the USB connector directly into

a USB port on your computer and not into a USB hub

or USB port on a keyboard or monitor.

Setting up

First, you have to answer a few questions to set up

your device. Answer the questions by tapping the

screen. You will use the touchscreen for everything

you do with your TomTom Rider.

Locating your current position

Your TomTom Rider must be outside to be able to

locate your current position. Make sure that you are

in an open place without tall buildings or trees

around you.

The first time you start your Rider, it can take a few

minutes for the device to find your current position.

In the future, your position will be found much

faster, normally within a few seconds.

Your Rider does not transmit your location, so oth-

ers cannot use it to track you while you are driving.

Mounting your navigation device

Attach the RAM™ mount kit to your motorcycle as

shown on the Installation Poster, then place your

Rider in the holder. When you are attaching the

mount kit to your motorcycle, follow these guide-

lines:

• If you are unsure about attaching the mount kit

yourself, ask a professional to fit it for you.

• Make sure that the mount kit does not interfere

with any of the controls on the motorcycle.

• Always use the correct tools. If you use unsuita-

ble tools, you may damage or break the mount

kit.

• Do not overtighten nuts. You may crack parts of

the mount kit or damage your handlebars if you

overtighten the nuts.

• If you are using the u-bolt, don’t forget to put the

rubber caps provided over the exposed threads.

Damage due to modifications, improper installa-

tion, road hazards or accident, are not covered. Nei-

ther RAM nor TomTom shall be liable for any injury,

loss, or damage, direct or consequential, arising out

of improper installation, or inability to use product.

Before use, the user shall determine the suitability

of the product for its intended use. The user

assumes all risk and liability, whatsoever, in con-

nection with the mount.

Rider3-UG.book Page 7 Friday, April 23, 2010 4:57 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TomTom Rider Pro Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TomTom Rider Pro

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info