Bedienungsanleitung Toolson Pro HMD1800PRO (Seite 15 von 108) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

781902

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

15 І 108

Sound emission

Noise emission values are measured according to the

relevant standards.

Sound pressure level LpA 90 dB(A)

Uncertainty K 3 dB(A)

Sound power level LwA 101 dB(A)

Uncertainty K 3 dB(A)

Vibration ah2.90 m/s²

Uncertainty K 1.5 m/s²

• The indicated vibration emission value has been

measured using a standardized test procedure and

can be used to compare one electric tool with ano-

ther;

• The indicated vibration emission value can also be

used in a preliminary exposure assessment.

• Depending on how the power tool is used, the vib-

ration emission value may differ from the specied

value when the power tool is actually used;

• Try to keep the exposure to vibrations as low as

possible. Actions reducing the exposure to vibration

include, for example, wearing gloves when the tool

is used and limiting the working time. Here, all as-

pects of the operating cycle must be considered (for

example, the times when the tool is turned off, and

those when the tool is turned on but running without

load).

Storage

• The whole machine and all accessories must be tho-

roughly cleaned.

• Store the machine always out of children’s reach.

Put it in a secure position in a dry and safe place

where no extremely high or extremely low tempera-

tures may occur.

• Protect the stored machine from direct sunlight; put

it in a darkened area, if feasible.

• Do not wrap the machine into bags or covers made

of nylon or plastic, as dampness may develop.

Switching on/off

Do not use any device where the switch can not be

switched on and off. Damaged switches must be

repaired or replaced immediately by the customer

service.

Switching on (Fig.5)

• Operate the trip switch (5) at rst. Press the ON/

OFF button (4) on the handle.

Start the machine at the lowest rotational speed

(Level 1).

Switching off

• Release the ON/OFF handle button.

This machine is not suited for continuous opera-

tion.

Speed control (Fig.6)

With this type, the motor‘s speed and thus the agitator

performance can be adjusted. (Level 1 - 6).

• You can continuously adjust the speed with the

speed control (6).

2- speed gear (Fig.7)

The device is equipped with a 2-speed gear.

• For the speed selection turn the switch (7) by 180°.

1. speed: 0 min–1 - 450 min–1

2. speed: 0 min-1 - 790 min-1

Only operate this switch at standstill.

Working with the paint and mortar mixing tool

Before changing the mixing tool you must pull the po-

wer plug.

Reduce the working speed when you immerse the mi-

xing tool into the material you want to mix and when

you take it out again. When the mixing tool is fully im-

mersed, raise the speed to maximum in order to ensu-

re adequate cooling of the motor. Move the mixing tool

through the mixing container during the mixing operati-

on. Continue mixing until all the material has been tho-

roughly processed. When you are nished with your

mixing work, clean the mixing tool.

Cleaning and Maintenance

ATTENTION!

Unplug the power plug from the electrical outlet

before starting any work on the power tool.

Cleaning

• Keep the air vents of the machine clean in order to

prevent overheating.

• Clean the machine’s casing regularly with a soft

cloth, preferably after each use.

• Keep the air vents free from dust and dirt.

• If the dirt cannot be removed easily, use a cloth that

is moistened with soapy water.

ATTENTION!

Do not use solvents such as benzene, alcohol, am-

monia solutions, etc. These solvents may damage

the plastic parts.

Technical data

Nominal voltage 230 V~, 50 Hz

Power consumption 1800 W

Speed 0-450 min-1 / 0-790 min-1

Weight 7.2 kg

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson Pro HMD1800PRO Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info