Bedienungsanleitung Topcom butler 2510 (Seite 17 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

300659

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

Topcom Butler 2505/2510 17

ENGLISH

6. MANAGING MULTIPLE HANDSETS

6.1. SETTING UP AN ADDITIONAL HANDSET

You can subscribe new handsets on the base if these handsets support the DECT GAP protocol.

The base can support a maximum of 5 handsets. If you already have 5 handsets, and you wish to add another one or

change one handset, you must first delete a handset, then associate the new handset.

To register any handset, the base must be put into a special registration mode:

1. Press and hold the paging key of the base for 6 seconds.

2. The base will then emit a beeptone. The base is now ready to register a new handset. You have 90 seconds after

pressing the button to register a new handset.

After putting the base into registration mode, start the procedure on the new handset:

if your additional handset is a butler 2505/2510/2550/2605/2610/2650/2705/2710/2750/2805/2810/2850

3. Enter the menu by pressing /OK

4. Select Register using the up and down keys

5. Press OK

6. Enter a base number ( from 1 to 4 ). The flashing numbers are already in use.

7. Enter the Base PIN code (0000 by default )

8. Press OK. The handset will start searching for the DECT base

9. If the handset has located the base, it will display the base identification number, validate the

base registration by pressing OK or stop by pressing ,

10. If the handset does not locate the base, it will return to the standby mode after a few seconds.

Try again by changing the base number and check that you are not in a environment where there

is interference. Move closer to the base.

if your handset is another model

After starting the registration procedure on the base, refer to the handset manual to find out how to register the handset.

The handset must be GAP compatible.

The icon and the text "NOT REG" flashes on the display when the handset is not associated with the base.

When a handset is associated with a base, it is attributed a handset number by the base. It is this number that is

displayed on the handset after the name and must be used for internal calls.

6.2 REMOVING A HANDSET

You can remove a handset with a base to allow another handset to be registered

1. Enter the menu by pressing /OK

2. Select setup using the up and down keys

3. Press OK

4. Select del hs using the up and down keys

5. Press OK

6. Enter the 4 digit base PIN code

7. Press OK

8. Select the handset to be removed

9. Press OK to validate

6.3 SETTING UP A HANDSET ON ANOTHER BASE

If you want to use a Butler 2505 or Butler 2510 handset with a base of another model. The base must be GAP

compatible.

1. To put the base in registration mode, refer to the base user manual.

2. Carry out operations 3 to 9 from the paragraph 6.1.

6.4 SELECTING A BASE

The handsets can be registered up to 4 bases simultaneously.

To select a base:

1. Enter the menu by pressing /OK

2. Select setup using the up and down keys

B2505_eur.book Page 17 Tuesday, December 31, 2002 11:49 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Topcom butler 2510 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info