Bedienungsanleitung Topcom butler 2900 (Seite 10 von 56) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

298476

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

10 Topcom Butler 2900 / Twin / Triple

Topcom Butler 2900 / Twin / Triple

6.4 ERASING A NUMBER FROM THE CALL LIST

• Scroll through the Call list until the desired number is shown on the display.

• Press and hold the Mute button for 3 sec. to erase the number.

6.5 STORE A NUMBER FROM THE CALL LOG INTO THE MEMORY

• Scroll through the Call list until the desired number is shown on the display.

• Press and hold the Memory button for 3 sec.

• Enter the memory location (0-9) where you want to store the number

• Enter the Memory button again to conﬁrm and to go back to standby

7. REGISTER/DE-REGISTER A HANDSET

7.1 REGISTER TO A TOPCOM B2900/2920 BASE

You can subscribe 5 handsets to one base unit. By default, each handset is subscribed as handset 1 on the base unit

upon delivery (base unit 1).

!!! You only need to subscribe the handset if: !!!

•The handset subscription has been removed from the base unit (e.g. for reinitialisation)

• You want to subscribe a different handset to this base unit.

The underlined procedure is only applicable to a Topcom Butler 29xx, 2900, 2920 handset and base unit!!

Keep the Paging key on the base unit pressed for 10 seconds until the Line/Charge indicator

on the base unit begins to blink rapidly. The Line/Charge indicator will blink rapidly

for one minute. During this minute, the base unit is in register mode and you must do the

following to subscribe the handset:

• Press and hold the and key for 3 sec.

•The following will appear on the display:

• Enter the number of the base unit you would like to subscribe the handset to (1-4)

•The unit will start searching for the base and when found it will ask to enter the pin code (4 digits):

• Enter the base pin code (0000). If the pin is wrong, the handset will restart the searching for the base.

•When the handset is registered, it will show ‘HS’ followed by the handset number.

7.2 SUBSCRIBING A TOPCOM BUTLER 300 DECT GAP HEADSET

Press the Paging key on the base unit for 10 seconds until the Line/charge indicator on the base unit starts to blink

quickly. The line/charge indicator will blink quickly for one minute. During this minute, the base unit is in subscribing

mode and you must do the following to subscribe the headset:

-Turn ON the headset by pressing the ON/OFF button until you hear two beep tones. At the same time the red and

green LED will lit ones.

- Remove the rubber cover of the power socket so that the hole of the power socket is free. Pull out the rubber cover

from the headset so that the registration key hole is free also.

- Press the headset registration key. The red LED will flash rapidly.

- If after a few seconds the green LED flashes slowly, the registration is successful.

- If the red LED flashes slowly, the registration is failed. Repeat above procedure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Topcom butler 2900 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info