Bedienungsanleitung Topcom Protalker PT-1078 (Seite 4 von 76) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

477785

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Protalker PT-1078

10 Charging the batteries

The desktop charger provides drop-in charging conveniency.

1. Put the desktop charger on a flat surface.

2. Plug one end of the supplied adapter into an easy accessible electric socket and the other end into the connector on the

backside of the desktop charger.

3. Make sure that the radio is turned OFF.

4. Put the radio in the charger.

5. The charging LED will turn on if it’s properly inserted and charging.

It will take about 16 hours to fully charge the Ni-Mh battery.

11 Description

See folded cover page - illustration 1

1. Antenna

2. LCD display

3. On/Off key

4. Speaker volume up

5. Speaker volume down

6. OK / Keylock - key

7. Menu key

8. Microphone

9. Speaker

10. Call key

11. Sub-channel/Group key SUB/GPR

12. Channel down

13. Channel up

14. Monitor key MON

15. PTT-key

12 LCD display information

See folded cover page - illustration 2

16. Channel indication

17. Call / Missed call icon

18. RX icon

19. Group icon

20. Sub channel/Menu item/Group number,... indication

21. Battery level indication

13 Using the PT-1078

13.1 Turning the Unit ON/OFF

13.2 Battery Charge Level / Low Battery Indication

The battery charge level is indicated by the battery icon on the LCD Screen.

Battery full

Battery low

Battery almost empty

13.3 Adjusting Speaker Volume

There are 8 speaker volume levels (0..7)

13.4 Receiving a signal

The unit is continuously in the receive mode when the unit is switched ON and not transmitting.

13.5 Transmitting a signal

13.6 Changing channels

13.7 Sub -channels : CTCSS (Continious Tone Coded Squelch System) /

DCS (Digital Coded Squelch)

License free PMR radio's operating on the 446 MHz frequency band, have 8 available radio channels. If there are many PMR users

in your neighborhood, there is a chance that some of these users are operating on the same radio channel.

To prevent that you receive signals from other users, sub-channels have been integrated.

Two PMR radio's will only be able to communicate with each other when they are operating on the same radio channel and when they

have selected exactly the same sub-channel.

There are two kind of sub-channels :

• Continuous Tone Coded Squelch System (CTCSS)

• Digital Coded Squelch (DCS)

When using CTCSS, a low frequency tone (between 67 and 250 Hz) will be transmitted along with the voice signal. There are 38

available tones to choose from. You are free to choose one of these 38 available tones. Due to filtering, these tones will generally not

be audible so they will not disturb the communication.

DCS is similar to CTCSS, but instead of sending a continuous tone of a selected frequency, a digital data transmission is added to the

radio signal. This Digital Code is transmitted at a really low rate, around 134 bits per second (the code is 23 bits long). Only the PMR's

To turn ON:

• Press and hold the - key for 2 seconds. The unit will “beep” and the LCD

display will display the current channel.

To switch OFF:

• Press and hold the - key for 2 seconds. The unit will “beep” and the LCD

display will turn blank.

Do not short-circuit the batteries or dispose in fire. Remove the batteries if this device is not going to

be used for a long period.

Do not charge non rechargeable batteries like Alkaline batteries in the charger. This might damage the

PMR’s and charger unit.

If the segments and icons of the displays are shown in light grey in this user guide, it indicates

that they are blinking.

In case the unit name is programmed, this name will be displayed for two seconds during startup

(Chapter 13.15.3).

• Press the - key in stand-by-mode to increase the speaker volume. The

volume level is displayed.

• Press the - key to decrease the speaker volume.

• Press the OK - key to confirm the volume level.

• Press and hold the PTT - key to transmit. The TX symbol is displayed.

• Hold the unit in a vertical position with the microphone 10cm from the mouth and

speak into the microphone .

• Release the PTT - key when you want to stop transmitting.

• Use the - key or the - key to go to a higher or lower

channel.

• After selecting the desired channel, press the OK - key to confirm.

When the battery is almost empty, will appear on the display and the unit will turn OFF automat-

ically after 30 seconds.

In order for other people to receive your transmission, they must also be on the same channel and have

set the same sub-channel (Chapter 13.6 and 13.7).

Protalker PT - 1078.book Page 4 Friday, June 4, 2010 1:58 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Topcom Protalker PT-1078 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info