Bedienungsanleitung Topro Troja S (Seite 8 von 19) (Deutsch, Englisch, Holländisch, Französisch, Norwegisch)

682617

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Important to know about safety when in use

• When stationary or parked, always use the parking brakes on both sides A

• Before sitting on the seat, make sure the parking brakes on both sides are in the locked position A

• Do not lean or bend sideways or over the back of the rollator whilst in the seated position.

• The driving brakes can be held in a little B to reduce speed, but must not be in locked position when the

walker is in motion.

• To give the right support and a safety, make sure the walker is kept as close to your body as possible C

• Walk straight, look forward and hold your backside in D. That is the easiest way to keep your balance.

• Do not push the walker too far from your body as this can cause unnecessary strain and you could fall.

• Be careful of flared skirts and trousers as they could get caught between the brake block and wheel,

which could lead to falling. We therefore recommend not wearing flared/wide clothing.

Assembling / adjusting

TOPRO TROJA is delivered assembled. Before use, you must unfold the rollator. The height of the handlebar

tubes will then need adjusting to suit the users needs.

Unfolding / folding

Unfolding: Loosen the strap between the forearm supports A. Loosen the lock clamp that is over the seat bars B.

Press the seat bars down and out C The side frames will slide apart. Press down the seat bars. You will hear a

clicking sound. The rollator is now locked in its open position. Fasten the strap A.

Folding: Pull the strap on the seat D and press the side frames together. Lock the clamp E over the seat bars.

Adjusting the handles and height adjustment of the forearm supports

Adjusting the handles: Unscrew the lock wheel A until the handle can be moved, adjust to the wanted position

and tighten the lock wheel again. It is done separately on each side. It is not possible to pull the handles all the

way out; there are physical stops both ways. Height adjustment: Unscrew the lock wheel B (approx. 4-5 turns).

Adjust the forearm support tubes to a suitable height, then pull them slightly up and down C until you hear a

clicking sound. Tighten the lock B again. Adjust both handlebars to the same height. Recommended height:

Stand with relaxed shoulders with your elbows in a 90 degree angle, see illustration 2.

Height adjustment using the memory function

You have the opportunity to set the height of the forearm supports at a standard setting fitting to your height so

that you easily can find the same height again. This can be necessary when the walker is being transported or

stored as compact as possible. Decide the height of the forearm support tube. Count visible holes at the back of

the tubes. Unscrew the lock wheel A. Pull the tube B out of the frame. The attached part C will now follow the

tube. Move the attached part C on the tube B so there are equal holes as counted earlier. Fit the memory chip D

on the tube in the first available hole under the attached part C. Push the tube B down and into the side frame E

until the attached part is locked. Screw the lock wheel A half in. Pull the tube B up until it stops, and then tighten

the lock wheel A properly. From now on, when the forearm support tubes are in the lowest position, they will stop

in the preset position automatically when pulled up.

Adjusting / checking and maintaining the brakes

Adjusting / checking: Loosen the nut A beside the brake. Tighten the brake wire B with the adjustment screw C.

Adjust both brake blocks so the distance to the wheel surface is approximately 1 mm D. Make sure the brakes

are not adjusted too tight and pressing into the rubber when the parking brake is on.

Maintaining: Clean the brake block E and the brake spring F frequently. The wheels can be changed if they are

worn out or damaged.

Using the brakes

Make sure the brakes work before each trip. Each brake handle A works on each of the rear wheels.

The rollator wheels are made of a special soft rubber which gives an optimal braking capacity on slippery floor.

Wrong use can cause unsafe situations and damage to the walker: The walker must not be driven or pushed

with force when the parking brakes are on or when the wheels are partly locked using the brakes. This

indicates incorrect use and can cause wear and tear which makes the tires and brake quality weaker.

Parking brakes: Push both brake levers A forwards until they lock. Both rear wheels are now locked. Pull the

brake levers back to release the parking brakes. Driving brakes: Squeeze both brake handles B upwards to

reduce speed. Do not use continuously while the walker is in motion.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Topro Troja S Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info