Bedienungsanleitung Tormatic NovoGate (Seite 19 von 43) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

710116

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

• Operating Instructions

These Operating Instructions describe how to use

the prodct properly and safely. The safety advice and

information as well as the accident prevention and

general safety regulations for the field of application

must be complied with.

(factory-set operating mode)

The sliding gate operator can be actuated by an

impulse generator, such as hand transmitter, key

switch etc. It is only necessary to generate a short,

sharp impulse.

In same operating mode as for single-lane control,

however, receiver remains plugged into operator.

Operator starts up and gate travels to open position.

No effect, gate continues to open.

Gate closes.

Gate stops and then reopens.

Red-green traffic light control is only possible

together with the additional A800 traffic light control

system. Generating an impulse always causes the

gate to open. After the green and clearance phase

has elapsed, gate automatically closes. If a new

opening impulse is generated during the green

phase, this is extended.

you may only drive through the gateway

during the green phase.

All persons using the gate system

must be shown how to operate it

properly and safely.

Keep hand transmitters out of the reach

of children.

When the operator is being used, the

opening and closing phases must be

monitored. It must be ensured that

neither persons nor objects are located

within the gate’s range of travel.

• Normal operation (0)

Normal operation (0)

OPEN-CLOSE operation (1)

Functional sequence:

Operation with single-lane control (1)

Caution:

Operating modes

Functional sequence:

Partial opening

IThe respective setting for menu 9 is shown in

brackets.

Operator starts up and causes gate to travel to set

open or closed travel limits.

Gate stops.

Gate continues to move but in opposite direction.

Partial opening of approx. 1 m instead of full opening

can be triggered by the hand tranmsitter or another

command generator.

First impulse:

IImpulse generated whilst gate is moving:

A new impulse:

Impulse generation in the closed position:

IImpulse generation whilst gate is opening:

Impulse generation in the open position:

Impulse generated whilst gate closes:

Automatic closing (2)

Automatic closing (3)

Automatic closing (4)

Functions of the safety devices

IInternal force limit device

Signal light

Disengaging the operator

Empty batteries must be disposed of separately

(toxic waste)!

Generating an impulse always causes the gate to

open.

IIf a photocell is installed, an interruption during the

closing phase causes the gate to stop and then travel

in the opposite direction. An interruption while the

gate is opening has no effect.

If a signal light to signal the opening and closing

phases is installed, this starts to flash as soon as a

start impulse is given. The operator starts up in

accordance with the set advance warning phase.

During the flashing phase, driving through the

gateway is not permitted.

When making adjustments and in the event of power

failures or malfunctions, the operator can be

disengaged and the gate be moved by hand. Open

and remove the cover with the triangular wrench.

Pull the pull cord with knob, 8 is displayed. The gate

can now be opened and closed by hand.

To resume power-operation, actuate the lever and

the operator re-engages. Replace the cover and lock

in place with the triangular wrench.

Programming further hand transmitters:

See menu stages 1 and 2 (figures 21 and 22).

Changing the battery: Slide back the battery

compartment cover on the hand transmitter.

Take out the battery.

Insert a new battery (alkaline 23A, 12V). Be sure to

pole correctly! Slide the cover back on.

After the hold-open phase and the advance warning

phase have elapsed, the gate automatically closes.

Generating an impulse always causes the gate to

open.

After the hold-open phase and the advance warning

phase have elapsed, the gate automatically closes.

If the photocell is interrupted, the hold-open phase is

prematurely terminated and the advance warning

phase commences.

Generating an impulse always causes the gate to

open.

After the hold-open phase and the advance warning

phase have elapsed, the gate automatically closes.

If an impulse is generated, the hold-open phase is

prematurely terminated and the advance warning

phase commences.

If the closing gate encounters an obstruction, the

operator stops and causes the gate to open to clear

the obstruction.

During the soft run of the closing phase, the gate is

opened a slight gap only, just sufficient to clear the

obstruction.

If during the opening phase the gate encounters an

obstruction, the operator stops and causes the gate

to reverse for approx. 1 sec.

Photocell

Hand transmitter

• Maintenance / Checks

The gate system must be inspected and

tested by a specialist company prior to

initial operation and at least once a year

thereafter.

Monitoring the force limit

Caution!

The operator control unit features a dual-processor

safety system to monitor the force limit.

The integral force cut-out is automatically tested at

each travel limit.

The gate system must be checked prior to initial

operation and at least once a year thereafter, In the

process, the force limiting device (figure 20) must be

tested!

If the closing force is set too high,

persons can be placed at risk of injury or

property could sustain damage.

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

Tormatic NovoGate Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info