Bedienungsanleitung Toshiba 19EL934G (Seite 13 von 41) (Englisch)

527562

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

English

English - 12 -

Initial Installation

Before switching on the television put your decoder and media recorder to Standby if they are connected and ensure the

aerial is connected to your television. To set up the television, use the buttons on the remote control as detailed on page 7.

IMPORTANT: Ensure that the aerial or cable is

connected and a Common Interface module is not

inserted before switching on the TV for the ﬁ rst time

installation.

1. Connect the mains plug and switch the TV on using

the side standby switch. Then the initial setup wizard

will be displayed. This wizard will appear the ﬁ rst time

that the television is switched on and each time the

television is reset.

Welcome to use the Wizard for Initial Setup!!

Please press [OK] to start the wizard.

2. Press the OK button to start the wizard.

3. Select your preferred language by pressing the

button, then press OK or to enter the next step.

4. Select your country by pressing the

or button, then

press OK or

to enter the next step.

Note: If you select France or Italy, you will be asked to

set a password. Use the digit buttons to enter a

four-digit number for your password. (0000 is too

simple to be set as your password.) Re-enter the

same code to conﬁ rm the password. After that,

you will enter the next step automatically. (At this

step, you can only press the

button to return to

the previous step.)

5. Select your location by pressing the

or button,

then press OK or to enter the next step. The location

options include Home and Retail.

Select Home and press OK to enter the next step. Use

the

or button to select your Tuner mode Antenna

or Cable.

Select Antenna.

• Press OK or

to enter.

• Press or to select a scan type

Digital&Analogue, Digital or Analogue and press

OK or

to enter the next step.

• Press

or to select Scan or Skip Scan,

Select Scan, then press OK or

to automatically start

searching for all available channels.

Select Cable.

• Press OK or

to enter.

• Press or to select a scan type

Digital&Analogue, Digital or Analogue and press

OK or

to enter the next step.

• Press or to select Scan or Skip Scan,

Select Scan, then press OK or

to enter the below

step.

• Select Full if available to search for and store all

available channels.

• You may select Advanced, then conﬁ gure proper

cable information such as Frequency, Modulation,

symbol rate and Network ID. Use the digit buttons

to input the values of frequency, symbol rate and

network ID; use the

or button to select a

modulation mode.

• Press OK to start initial setup for all available

channels.

Note: The searching progress bar will move along the

line. You must allow the television to complete

the search. During the search, pressing EXIT

will interrupt the search halfway and go back to

the previous step.

6. You can also skip the initial setup process by selecting

Skip Scan.

7. During the setup, you can follow the hints available at

the bottom of the screen to return to the previous step

by pressing the

button.

8. After the initial setup ﬁ nishes, press OK to display the

channel list.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba 19EL934G Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba 19EL934G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info