Bedienungsanleitung Toshiba 40TL938G (Seite 17 von 98) (Englisch)

527534

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

SETTING UP YOUR TV

English

o Press OK. If your country supports Network Guide,

The Guide Type screen will appear.

Press

C or c to select Broadcast Guide or

MediaGuide.

NOTE: If you select MediaGuide, it may take time to

access the Guide screen depending on active channel

numbers.

p Press OK. If the Ant/Cable In screen appears, press B

b to select Antenna or Cable, and then press OK

to check ( ).

q Select Next and press OK. The Auto Tuning start up

screen will appear with the option to select between

DTV and ATV, DTV or ATV if available. Use

C or c to

select the appropriate mode.

r Press B or b to highlight Start Scan, and then press

OK.

The television will start to search for available DTV

and/or ATV channels. The progress bar will indicate

the scan status.

You must allow the television to complete the

search.

When the search is complete, the television will

automatically select channel one.

The Auto Tuning screen will display the total number

of services found.

s Press C or c to view the DTV (digital channel) or ATV

(analogue channel) lists.

T Use B or b to move through the list to select a

channel, and then press OK to view.

In ATV mode, some areas may receive duplicate

stations. There may not be a clear picture or the signal

may be weak, so the station order can be changed

using ATV Manual Tuning.

REMEMBER: Press TV at any time to select between

ATV and DTV modes.

NOTE: The time will be set automatically by

transmission but can be advanced or decreased by

using Local Time Setting in the DTV Settings screen.

From this menu, you can set the RF input configuration.

a Press MENU / C c to highlight Setup icon.

b Press B / C c to highlight System Setup icon and

press OK.

c Press b to select Ant/Cable In and press C or c to

select Antenna or Cable.

NOTE: When you attempt to change the Ant/Cable

In setting, a warning message will appear followed by

PIN entry (if PIN has been set) and a prompt for Auto

Tuning.

d When Ant/Cable In is set to Cable, the following

setting options will be provided in the Auto Tuning

screen.

Press

B or b to select an item and press C or c to

select your desired option.

TV Guide Selection

Broadcast Guide

Electronic Program Guide accessed by the “GUIDE” key of your

remote control:

Select “MediaGuide” if you want to use the advanced rich media

EPG provided through the network.

*Your TV must be connected to the network.

Select “Broadcast Guide” if you want to use the simple EPG

provided by our local broadcast network, if any.

Ant/Cable In

Cable

Antenna

Auto Tuning - Antenna

Progress Found

ATV Tune Waiting...

: C7Channel

DTV Tune 3 % 2

Ant/Cable In (if available)

The Quick Setup menu can also be accessed at any

time from the Setup / System Setup menu.

PLEASE NOTE

Auto Tuning - Cable

DTV and ATVTuning Mode

DTV

OthersOperator Selection

Quick ScanScan Type

AutoStart Frequency

AutoEnd Frequency

AutoModulation

AutoSymbol Rate

AutoNetwork ID

Start Scan

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba 40TL938G Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba 40TL938G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info