45983
36
Zoom out
Zoom in
Vorherige Seite
1/74
Nächste Seite
36
XV540U (E/F) Web 213:276
Chapter 5: Setting up your TV
Configuring the input source for the
ANT/CABLE terminal
To configure the ANT/CABLE input source:
1 Press Y and open the Setup menu.
2 Highlight Installation and press T. A new set of
Installation menu icons will appear, as shown below.
3 Open the Terrestrial menu, highlight Input
Configuration, and press T.
4 Press B and C c to select the input source (Cable or
Antenna) for the ANT/CABLE input on the TV.
5 To save your new settings, highlight Done and press T.
To revert to your original settings, highlight Cancel and
press T.
Programming channels into the
TV’s channel memory
When you press < or , on the remote control or TV control
panel, your TV will stop only on the channels you programmed
into the TV’s channel memory.
Follow the steps below to program channels into the TV’s
channel memory.
Programming channels automatically
Your TV can automatically detect all active channels in your
area and store them in its memory. After the channels are
programmed automatically, you can manually add or erase
individual channels in the channel memory.
Note:
If the ANT/CABLE input signal type is set to Cable, the
automatic channel programming process erases channels
that were previously programmed into the TV’s memory.
If the ANT/CABLE input signal type is set to Antenna, the
automatic channel programming process adds newly found
channels to the existing set of programmed channels (and
does NOT erase channels that were previously
programmed into the TV’s memory.) To remove an Antenna
source channel from the memory, you must manually delete
it.
To tune the TV to a channel not programmed in the channel
memory, you must use the Channel Number buttons on the
remote control.
Programming channels when the ANT/CABLE input is
configured for Cable will take substantially longer than when
the ANT/CABLE input is configured for Antenna. This is
normal; however, once channel programming is finished,
you should not have to repeat the programming process
again unless your Cable TV service lineup changes
significantly.
To program channels automatically:
1 You must configure the ANT/CABLE input source, if
you have not already done so (
- page 36).
2 From the Setup menu, highlight Installation and press
T. A new set of Installation menu icons will appear.
Installation
REGZA-LINK Setup
PC Settings
Power-On Mode
Demo Mode Off
Setup
Sleep Timer
HDMI Settings
Power-Saving
Installation
Terrestrial
Input Configuration
Channel Program
Channel Add/Delete
Channel Tuning Mode Auto
Signal Meter
Input Configuration
ANT/CABLE In Cable
Cancel Done
42XV540U_EN.book Page 36 Thursday, March 6, 2008 11:06 AM
36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Toshiba 42XV540 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info