Bedienungsanleitung Toshiba 43UL2163 (Seite 16 von 46) (Englisch)

804236

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

English - 15 - (**) Limited Models Only

and press OK you can select Network or set values

such as Frequency, Network ID and Search Step on

the next screen. If you select No and press OK or the

network search dialogue is not displayed you can set

Start Frequency, Stop Frequency and Search Step

on the next screen. When finished, highlight Next and

press OK button to continue.

Note: Searching duration will change depending on the

selected Search Step.

Satellite: If Satellite broadcast search option is turned

on, the TV will search for digital satellite broadcasts

after other initial settings are completed. Before

satellite search is performed some settings should

be made.

Depending on the model and the selected country

the next step may be the selection of the installation

type for satellite. You can select to start an operator

installation or a standard installation at this point. If you

want to perform an operator installation set the Install

Type as Operator and then set the Satellite Operator

according to your operator preference. Some of the

following steps may differ or be skipped depending on

the selected operator in this step. If you set the Install

Type as Standard, you can continue with regular

satellite installation and watch satellite channels.

Press OK to proceed.

M7 Operator Option (**)

To start an M7 operator installation set the Install

Type as Operator when prompted and the Satellite

Operator as the related M7 operator. Then highlight

Preferred Scan option and set as Automatic

channel scan and press OK to start the automatic

search. These options can be preselected depending

on the language and country selections that you

made in the earlier steps of the first time installation

process. You may be asked to select HD/SD or

country specific channel list according to your M7

operator type. Select one and press OK to proceed.

Wait till the scan is finished. Now the list has been

installed.

While performing an M7 operator installation, if you

want to use the satellite installation parameters that

differ from the default settings select the Preferred

Scan option as Manual channel scan and press the

OK button to proceed. Antenna type selection screen

will be displayed next. After selecting the antenna

type and the desired satellite in the following steps

press OK in order to change the satellite installation

parameters in the sub-menu.

Fransat Option (**)

To start a Fransat installation set the Install Type as

Operator when prompted and than set the Satellite

Operator as the related Fransat operator. Then press

the OK button to start Fransat installation. You can

select to start an automatic or manual installation.

Press OK to proceed. Fransat Installation will be

performed and broadcasts will be stored (if available).

If you set the Install Type as Standard, you can

continue with regular satellite installation and watch

satellite channels.

You can start a Fransat installation at any time later

from the Settings>Installation>Automatic channel

scan> Satellite menu.

Antenna type selection screen may be displayed

next. You can select Antenna type as Direct, Single

Satellite Cable or DiSEqC switch by using Left or

Right directional buttons. After selecting your antenna

type press OK to see the options to proceed. Continue,

Transponder list and Configure LNB options may be

available. You can change the transponder and LNB

settings using the related menu options.

• Direct: If you have a single receiver and a direct

satellite dish, select this antenna type. Press OK to

continue. Select an available satellite on the next

screen and press OK to scan for services.

• Single Satellite Cable: If you have multiple receivers

and a single satellite cable system, select this anten-

na type. Press OK to continue. Configure settings

by following instructions on the next screen. Press

OK to scan for services.

• DiSEqC switch: If you have multiple satellite dishes

and a DiSEqC switch, select this antenna type. Then

set the DiSEqC version and press OK to continue.

You can set up to four satellites (if available) for

version v1.0 and sixteen satellites for version v1.1

on the next screen. Press OK button to scan the first

satellite in the list.

Note: Depending on the model of your TV, DiSEqC version

v1.1 may not be supported and therefore the DiSEqC version

selection step may not be available.

Analogue: If Analogue broadcast search option is

turned on, the TV will search for analogue broadcasts

after other initial settings are completed.

A dialogue screen asking to activate parental control

will be displayed. If you select Yes, parental restriction

options will be displayed. Configure as desired and

press OK when finished. Select No and press OK

to advance, if you don’t want to activate parental

restrictions.

After the initial settings are completed the TV will start

to search for available broadcasts of the selected

broadcast types.

While the search continues current scan results will be

displayed at the bottom of the screen. You can press

the Home, Back or Exit button to cancel the search.

The channels that have already been found will be

stored in the channel list.

After all the available stations are stored, Channels

menu will be displayed. You can edit the channel

Toshiba 43UL2163 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba 43UL2163

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info