Bedienungsanleitung Toshiba 50M8365 (Seite 18 von 103) (Englisch)

560422

Zoom out

Zoom in

Vorherige Seite

1/103

Nächste Seite

English

SETTING UP YOUR TV

s Press b to highlight Start Scan, and press OK.

The television will start to search for available DTV

and/or ATV channels. The progress bar will

indicate the scan status.

You must allow the television to complete the

search.

When the search is complete, the television will

automatically select channel one.

The Auto Tuning screen will display the total

number of services found.

T Press C / c to view the DTV (digital channel) or

ATV (analogue channel) lists.

u Press B / b to move through the list to select a

channel, and then press OK to view.

In ATV mode, some areas may receive duplicate

stations. There may not be a clear picture or the

signal may be weak, so the station order can be

changed using ATV Manual Tuning.

REMEMBER: Press TV at any time to select

between ATV and DTV modes.

NOTE: The time will be set automatically by

transmission but can be advanced or decreased

by using Local Time Setting in the DTV Settings

screen.

v Select Next and press OK. The Satellite Settings

screen will appear. From this window, you can add

the satellites that you wish to tune and configure

detailed settings for each one individually.

Select Switch Type and choose the correct switch

configuration for your satellite dish from the

settings None, ToneBurst, DiSEqC 2way,

DiSEqC 4way or Single cable.

NOTE:

• None is being used when the satellite dish will

control only one universal Low Noise Block

(LNB) with a single satellite (e.g. Astra 19.2°). As

a rule, most households use just one satellite.

• ToneBurst sends a 22 kHz signal. ToneBurst is

only necessary for simple LNBs (not universal

LNBs). The 22 kHz signal is needed for

switching LNBs with multifeed signals as well as

for changing between low- and high-band.

• DiSEqC 2way automatically switches between

two LNBs, which receive different satellites at the

same time (e.g. Astra 19.2° and Hotbird 13°).

• DiSEqC 4way automatically switches between

up to four LNBs / satellites.

• Single cable is selection and control of plural

Satellite antennas through the combined single

antenna cable.

The setting LNB Power enables you to switch on

or off the LNB's power supply by means of the TV.

When your satellite dish consists of only one LNB,

LNB Power should generally be activated (On).

When using more than two LNBs, it is

recommendable to use external power supply for

these.

It is possible to select up to four satellites. Please

note that the number of available LNBs and the

adjustment of your satellite dish determines the

number of satellites found. For example, it is not

possible to receive more than one satellite if your

dish is directed to a single satellite. For further

information on satellite signal technology, please

contact your local dealer.

Auto Tuning - Antenna

Channel: 23

Progress

DTV Tune

ATV Tune

4 %

Waiting...

Found

1 Astra 19.2E 1 1

None

ToneBurst

DiSEqC 2way

DiSEqC 4way

Single Cable

Satellite Settings

Switch Type

LNB Power

None

No. Satellite

Dish

LNB

Done

1 Astra 19.2E 1 1

Off

Satellite Settings

Switch Type

LNB Power

None

No. Satellite

Dish

LNB

Done

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba 50M8365 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba 50M8365

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info