Bedienungsanleitung Toshiba 55U2963 (Seite 12 von 36) (Englisch)

698391

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

English - 11 -

option will be checked. To turn the search option off

clear the checkbox by pressing OK after moving the

focus on the desired broadcast type option.

Digital Aerial: If  broadcast search option

is turned on, the TV will search for digital terrestrial

broadcasts after other initial settings are completed.

 If  broadcast search option

is turned on, the TV will search for digital cable

broadcasts after other initial settings are completed.

A message will be displayed before starting to search

asking if you want to perform cable network search. If

you select Yes and press OK you can select 

or set values such as ,  and

Search Step on the next screen. If you select 

and press OK you can set Start , Stop

 and Search Step on the next screen.

When finished, highlight  and press OK button

to continue.

Note: Searching duration will change depending on the

selected Search Step.

Satellite: If Satellite broadcast search option is turned

on, the TV will search for digital satellite broadcasts

after other initial settings are completed. Before

satellite search is performed some settings should

be made. A menu will be displayed where you can

select to start  operator installation or

a standard installation.

To start an M7 operator installation set the Install Type

as Operator and the Satellite Operator as the related

M7 operator. Then highlight Preferred Scan option

and set as Automatic channel scan and press OK

to start the automatic search. These options can be

preselected depending on the  and Country

selections that you made in the earlier steps of the first

time installation process. You may be asked to select

HD/SD or country specific channel list according to

your M7 operator type. Select one and press OK to

proceed.

Wait till the scan is finished. Now the list has been

installed.

While performing an M7 operator installation, if you

want to use the satellite installation parameters that

differ from the default settings select the Preferred

Scan option as Manual channel scan and press the

OK button to proceed. Antenna Type menu will be

displayed next. After selecting the antenna type and

the desired satellite in the following steps press OK

in order to change the satellite installation parameters

in the sub-menu.

To start a  installation set the Install Type as

Operator and then set the Satellite Operator as the

related Fransat operator. Then press the OK button

to start installation. You can select to start an

automatic or manual installation.

Press OK to proceed. Fransat Installation will be

performed and broadcasts will be stored (if available).

If you set the Install Type as Standard, you can

continue with regular satellite installation and watch

satellite channels.

You can start a Fransat installation at any time later

from the Settings>Installation>Automatic channel

scan> Satellite menu.

In order to search for satellite channels other than

M7 or Fransat channels you should start a standard

installation. Select the Install Type as Standard and

press the OK button to proceed. Antenna Type menu

will be displayed next.

There are three options for antenna selection. You can

select Antenna Type as Direct, 

or   by using Left or Right buttons.

After selecting your antenna type press OK to see

the options to proceed. Continue, Transponder list

and  options will be available. You can

change the transponder and LNB settings using the

related menu options.

 Direct: If you have a single receiver and a direct

satellite dish, select this antenna type. Press OK to

 Select an available satellite on the next

screen and press OK to scan for services.

    If you have multiple

receivers and a single satellite cable system, select

this antenna type. Press OK to continue. Configure

settings by following instructions on the next screen.

Press OK to scan for services.

  If you have multiple satellite dishes

and a , select this antenna type. Then

set the DiSEqC version and press OK

You can set up to four satellites (if available) for

version v1.0 and sixteen satellites for version v1.1

on the next screen. Press OK button to scan the first

satellite in the list.

Analogue: If Analogue broadcast search option is

turned on, the TV will search for analogue broadcasts

after other initial settings are completed.

A dialogue screen asking to activate parental control

will be displayed. If you select Yes, parental restriction

options will be displayed. Configure as desired and

press OK when finished. Select  and press OK

to advance, if you don’t want to activate parental

restrictions.

After the initial settings are completed TV will start

to search for available broadcasts of the selected

broadcast types.

While the search continues current scan results will

be displayed at the bottom of the screen. After all the

available stations are stored, Channels menu will be

displayed. You can edit the channel list according to

your preferences using the Edit tab options or press

the Menu button to quit and watch TV.

Toshiba 55U2963 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba 55U2963

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info