Bedienungsanleitung Toshiba 58UA2D63 (Seite 15 von 47) (Englisch)

804196

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

English - 14 - (**) Limited Models Only

Satellite

If Satellite option is selected, Antenna Type screen

will be displayed next. If you have a Direct satellite

system, you can proceed to the next step quickly by

selecting the Next option here. Highlight More and

press OK to set the antenna type manually. Single,

Tone Burst, DiSEqC and Unicable options are

available. Highlight the antenna type that corresponds

to your satellite system and press OK or the Right

directional button to proceed to the next step.

Next screen will be Select Operator screen. You

can select only one operator from the list. Highlight

the desired operator and press OK or the Right

directional button to proceed. Some of the options in

the following steps may be preset and/or additional

steps may be added or some steps may be skipped

depending on the selected operator in this step. Check

the parameters in each step before proceeding and

adjust if necessary. You can highlight General and

press OK or Right directional button to proceed with

normal satellite installation.

LNB List screen will be displayed next. You may be

    󰀨    

selected country, antenna type and operator in the

previous steps. Highlight the desired satellite option

and press OK or the Right directional button to set

the parameters. The Satellite Status of the first

satellite option will be set as On. In order to enable

channel scan on the satellite, this option should be

set as On

Following satellite parameters will be available. You

may not be able to change all settings depending on

the previous selections.

Satellite Status: Set the status option to On to

enable channel search on the selected satellite.

Highlight this option and press OK to change the

status.

Satellite Selection: Select the satellite on which you

want to perform a channel search.

Scan Mode: Set your scan mode preference. Full

and Network options will be available. If you are

going to perform a network scan, make sure that

you have adjusted the Frequency, Symbol Rate

(Ksym/s) and Polarisation parameters under the

Transponder option accurately.

Scan Type: You can perform a scan for free or

encrypted channels only. If the Free option is

selected encrypted channels will not be installed.

Select All to scan all channels.

Store Type: You can select to store TV channels

(referred to as ‘Digital Channels’ in the menu) or

radio channels only. Select All to store all channels.

Transponder: Adjust the Frequency, Symbol Rate

(Ksym/s) and Polarisation parameters for the

selected satellite if necessary.

LNB Congurations: Set the parameters for LNB.

For DiSEqC antenna type select the correct DiSEqC

port corresponding to your satellite system. Set other

parameters in accordance with your satellite system

if necessary.

Signal Quality: The signal quality status is displayed

as a percentage.

Signal Level: The signal level status is displayed

as a percentage.

Press the Back/Return button and select next satellite



changes, highlight Next on the LNB List screen and

press OK or Right directional button to proceed.

If Load Preset List option is selected in the previous

step next steps will be skipped and the preset channel

list installation will start. If the correct satellite has not

been selected for SatcoDX installation, a warning

dialogue will be displayed on the screen. The satellite/s

that can be selected will be listed. Press OK to close

the dialogue and then set the satellite accordingly.

Channel Scan screen will be displayed next. Select

Skip Scan to proceed without performing a scan

and complete the initial setup. Select Only digital

channels and press OK or the Right directional button

to start the search. While the search continues you can

press the Back/Return button, highlight Skip Scan

and press OK or Right directional button to stop the

search. The channels that have already been found

will be stored in the channel list.

When the initial setup is completed a message will be

displayed. Press OK

You will be asked to give your consent to the

collection of your data. Read the text on the screen

for detailed information. Highlight Accept and press

OK to give your consent and proceed. To skip

without giving your consent, select Skip. You can

change this setting later using the Settings>Device

Preferences>Manufacturer Usage & Diagnostics

menu.

Home Screen will be displayed. You can press the Exit

button on the remote to switch to Live TV mode and

watch TV channels.

Home Screen



be connected to the Internet. Connect the TV to a

home network with a high-speed Internet connection.

You can connect your TV wirelessly or wired to your

modem/router. Refer to the Network & Internet

and Connecting to the Internet sections for further

information on how to connect your TV to the Internet.

The Home menu is the centre of your TV. From the

Home menu, you can start any application, switch to a

TV channel, watch a movie, or switch to a connected

Toshiba 58UA2D63 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba 58UA2D63

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info