Bedienungsanleitung Toshiba 65U6763 (Seite 12 von 35) (Englisch)

681926

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

English - 11 -

Switching On/Off

To Switch the TV On

Connect the power cord to a power source such as a

wall socket (220-240V AC, 50 Hz).

To switch on the TV from standby mode either:

• Press the Standby button, Programme +/- or a

numeric button on the remote control.

• Press the centre of the joystick on the TV in or push

it up/down until the TV comes on from standby.

To Switch the TV Off

Press the Standby button on the remote control or

press the centre of the joystick on the TV in and hold

it down for a few seconds, the TV will switch into

standby mode.

To power down the TV completely, unplug the

power cord from the mains socket.

Note: When the TV is switched into standby mode, the

standby LED can blink to indicate that features such as

Standby Search, Over Air Download or Timer is active. The

LED can also blink when you switch on the TV from standby

mode.

First Time Installation

Note: If you are going to perform FRANSAT installation, insert

the FRANSAT card (optional) into the Conditional Access

terminal of your TV before switching on your TV.

When turned on for the first time, the language

selection screen is displayed. Select the desired

language and press OK.

On the next screen, set your preferences using the

directional buttons.

Note: Depending on the Country selection you may be asked

to set and conrm a PIN at this point. The selected PIN cannot

be 0000. You have to enter it if you are asked to enter a PIN

for any menu operation later.

About Selecting Broadcast Type

Digital Aerial: If Digital Aerial broadcast search

option is turned on, the TV will search for digital

terrestrial broadcasts after other initial settings are

completed.

Digital Cable: If Digital Cable broadcast search

option is turned on, the TV will search for digital cable

broadcasts after other initial settings are completed.

According to your other preferences a conrmation

message may be displayed before starting to search.

Select YES and press OK to proceed. To cancel

operation, select NO and press OK. You can select

Network or set values such as Frequency, Network

ID and Search Step. When nished, press OK button.

Note: Searching duration will change depending on the

selected Search Step.

Satellite: If Satellite broadcast search option is

turned on, the TV will search for digital satellite

broadcasts after other initial settings are completed.

Before satellite search is performed some settings

should be made. Before the satellite search starts,

a menu will be displayed where you can select to

start a Fransat installation. Set the Install Type as

Operator and than set the Satellite Operator as the

related Fransat operator. Then press the OK button

to start Fransat installation. You can select to start an

automatic or manual installation.

Press OK to proceed. Fransat Installation will be

performed and broadcasts will be stored (if available).

If you set the Install Type as Standard, you can

continue with regular satellite installation and watch

satellite channels.

You can start a Fransat installation at any time later

from the Installation>Automatic channel scan>

Satellite menu.

There are three types of antenna selection. You can

select Antenna Type as Direct, Single Satellite

Cable or DiSEqC switch by using “ ” or “ ” buttons.

• Direct: If you have a single receiver and a direct

satellite dish, select this antenna type. Press OK to

continue. Select an available satellite on the next

screen and press OK to scan for services.

• Single Satellite Cable: If you have multiple

receivers and a single satellite cable system, select

this antenna type. Press OK to continue. Congure

settings by following instructions on the next screen.

Press OK to scan for services.

• DiSEqC switch: If you have multiple satellite dishes

and a DiSEqC switch, select this antenna type.

Press OK to continue. You can set four DiSEqC

options (if available) on the next screen. Press OK

button to scan the rst satellite in the list.

Analogue: If Analogue broadcast search option is

turned on, the TV will search for analogue broadcasts

after other initial settings are completed.

Additionally you can set a broadcast type as your

favourite one. Priority will be given to the selected

broadcast type during the search process and the

channels of it will be listed on the top of the Channel

List. When nished, press OK to continue.

A dialogue screen asking to activate parental control

will be displayed. If you select Yes, parental restriction

options will be displayed. Congure as desired and

press OK when nished. Select No and press OK

to advance, if you don’t want to activate parental

restrictions.

You can activate Store Mode option at this point.

This option will congure your TV’s settings for store

environment and depending on the TV model being

used, the supported features of it may be displayed

on the top of the screen as an info banner. This option

is intended only for store use. It is recommended to

select Home Mode for home use. This option will be

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba 65U6763 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba 65U6763

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info