Bedienungsanleitung Toshiba e-STUDIO 205 (Seite 196 von 226) (Englisch)

481922

196

Zoom out

Zoom in

Vorherige Seite

1/226

Nächste Seite

6 TROUBLESHOOTING

194 Before Calling Service Technician

Before Calling Service Technician

When you encounter trouble using this equipment, check the items listed below.

General operation

Phenomenon Usual cause Countermeasure

The equipment does not

operate at all.

The power cable is not

plugged in securely.

Plug in the power cable securely.

The weekly timer functions

and the equipment is in the

sleep mode.

Press any button on the control panel.

The equipment does not

operate even when you press

any of the buttons.

A message appears on the

screen.

Check the message and take any coun-

termeasure accordingly.

 P.172 “When This Message Appears”

The equipment is in the

energy saving mode.

Press the [ENERGY SAVER] button to

cancel this mode.

 P.34 “Saving energy when not in use -

Energy saving mode -”

When the use of the equip-

ment is managed under

department management,

and the department code

has not been entered.

Enter your department code.

 P.33 “Preparation 1 - Turning Power

ON”

 P.143 “Department Code”

It has been a short time

since the power was turned

ON.

Wait for the completion of warm-up and

then try again.

Scanning stops in the mid-

dle. (“Count over” appears on

the display.)

The number of pages

scanned has exceeded the

maximum value.

Select “Print” on the LCD screen to copy

the data scanned so far. Select “Cancel

job” to delete all the data scanned so far.

Scanning stops in the mid-

dle. (“Memory is full” appears

on the display.)

The built-in memory of the

equipment has become full.

Select “Print” on the LCD screen to copy

the data scanned so far. Select “Cancel

job” to delete all the data scanned so far.

Copying stops in the middle.

(“Clear paper output tray:

PRESS START KEY.”

appears on the display.)

Approx. 250 sheets of paper

have continuously exited and

the equipment stops copy-

ing to prevent the copied

paper from overflowing from

the tray.

Remove the paper from the receiving tray,

and then press the [START] button. Copy-

ing resumes.

Press the [CLEAR/STOP] button to end

the copy job. “Memory clear?” appears on

the LCD screen. Select “YES”, and then

press the [START] or [ENTER] button.

“Saving energy” appears on

the display.

The equipment is in the low

power mode.

The equipment automatically enters into

this mode when a specified period of time

has passed since its last use. Copying is

enabled.

“Sleep mode” appears on the

display.

The equipment is in the

sleep mode.

The equipment automatically enters into

this mode when a specified period of time

has passed since its last use. Warm-up

starts either when print data are received

or when any button on the control panel is

pressed. Copying is enabled when the

warm-up has finished.

Copy functions cannot be set. Other functions that cannot

be set simultaneously with

copy functions have been

set.

Some functions cannot be combined set

together.

 P.211 “Copying Function Combination

Matrix”

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba e-STUDIO 205 Seite 196

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba e-STUDIO 205

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info