Bedienungsanleitung Toshiba E-STUDIO 306CS (Seite 8 von 338) (Englisch)

804397

Zoom out

Zoom in

Vorherige Seite

1/338

Nächste Seite

•Turn the printer o using the power switch, and then unplug the power cord from the electrical outlet.

•Disconnect all cords and cables from the printer before moving it.

•Lift the printer o the optional tray, and then set it aside instead of trying to lift the tray and printer at the

same time.

Note: Use the handholds located on both sides of the printer to lift it.

CAUTION—POTENTIAL INJURY: To avoid the risk of ﬁre or electrical shock, use only the power cord

provided with this product or the manufacturer's authorized replacement.

Use only the telecommunications (RJ‑11) cord provided with this product or a 26 AWG or larger replacement

when connecting this product to the public switched telephone network.

CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, if you are accessing the controller

board or installing optional hardware or memory devices sometime after setting up the printer, then turn

the printer o, and unplug the power cord from the electrical outlet before continuing. If you have any

other devices attached to the printer, then turn them o as well, and unplug any cables going into the

printer.

CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, make sure that all external

connections (such as Ethernet and telephone system connections) are properly installed in their marked

plug-in ports.

This product is designed, tested, and approved to meet strict global safety standards with the use of speciﬁc

manufacturer's components. The safety features of some parts may not always be obvious. The manufacturer

is not responsible for the use of other replacement parts.

CAUTION—POTENTIAL INJURY: Do not cut, twist, bind, crush, or place heavy objects on the power

cord. Do not subject the power cord to abrasion or stress. Do not pinch the power cord between objects

such as furniture and walls. If any of these things happen, a risk of ﬁre or electrical shock results. Inspect

the power cord regularly for signs of such problems. Remove the power cord from the electrical outlet

before inspecting it.

Refer service or repairs, other than those described in the user documentation, to a service representative.

CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock when cleaning the exterior of the

printer, unplug the power cord from the electrical outlet and disconnect all cables from the printer before

proceeding.

CAUTION—SHOCK HAZARD: To avoid the risk of electrical shock, do not set up this product or make

any electrical or cabling connections, such as the power cord, fax feature, or telephone, during a

lightning storm.

CAUTION—TIPPING HAZARD: Installing one or more options on your printer or MFP may require a

caster base, furniture, or other feature to prevent instability causing possible injury. For more information

on supported conﬁgurations, contact the place where you purchased the printer.

CAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability, load each tray separately.

Keep all other trays closed until needed.

SAVE THESE INSTRUCTIONS.

Safety information 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba E-STUDIO 306CS Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba E-STUDIO 306CS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info