Bedienungsanleitung Toshiba e-studio 355 (Seite 26 von 80) (Englisch)

481883

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

Chapter 1 PREPARATIONS

Saving energy when not in use – energy saving modes -

This equipment supports three energy saving modes; the Automatic Energy Save mode, Sleep mode and Super Sleep

mode. The table below shows the procedures to switch modes manually and the conditions under which the equipment

enters into or recovers from each mode.

Refer to the MFP Management Guide for changing the default settings noted above.

For the European version

Contact your service representative to change the default settings noted above.

Energy saving

modes

Procedure to switch

modes

Conditions to enter into

the mode Status of equipment Conditions to recover

from the mode

Automatic Energy

Save mode

When a specied period of

time *1 has passed since

the last use of the

equipment.

–

"Saving energy - press

START button" appears on

the touch panel.

When a button on the

control panel *4 is pressed

or when print data or fax

data are received.

Sleep mode

When the [ENERGY SAVER]

button

is pressed or

when a specied period of

time

has passed since the

last use of the equipment.

When a particular option *2

is installed or when a

particular protocol *3 is

enabled.

"Saving energy – press

START button" goes o

and the [ENERGY SAVER]

button lights in green.

Same as the Automatic

Energy Save mode.

Super Sleep mode

When the [ENERGY SAVER]

button

or the [POWER]

button

is pressed or

when a specied period of

time

has passed since the

last use of the equipment.

When a particular option *2

is not installed and also

when a particular protocol

*3 is disabled.

Only the MAIN POWER

lamp lights.

When the [POWER] button

is pressed and held until

the ON/OFF lamp lights,

when print data or fax

data are received through

a wired LAN or when the

time set for Scheduled

Print has come.

*1 The default value set at the factory shipment is 1 minute.

*2 Any of the Wireless LAN Module, Bluetooth Module and e-BRIDGE ID Gate.

*3 Any of IPX, AppleTalk and other protocols. When the IPsec function is enabled, the equipment enters into the Sleep mode. Refer to the TopAccess

Guide for details.

*4 Any of the [START], [ENERGY SAVER], [COPY], [e-FILING], [SCAN], [PRINT] and [FAX] buttons.

*5 Even if you press the [Power] button, the equipment may not enter into the Super Sleep mode and the power may be turned OFF, depending on the

state of the equipment. Refer to the TopAccess Guide for the conditions under which the equipment enters into the Super Sleep mode.

*6 [ENERGY SAVER] button on the control panel shown below.

When the set period of time for switching to the Automatic Energy Save mode is the same as that for the Sleep mode or

the Super Sleep mode, the equipment enters into the Sleep mode or the Super Sleep mode after the set period of time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba e-studio 355 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba e-studio 355

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info