Bedienungsanleitung Toshiba e-studio 4540C (Seite 18 von 82) (Englisch)

481873

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

Chapter 1 PREPARATIONS

Saving energy when not in use – energy saving modes –

This equipment supports three energy saving modes; the Automatic Energy Save mode, Sleep mode and Super Sleep

mode. The table below shows the procedures to switch modes manually and the conditions under which the equipment

enters into or recovers from each mode.

Energy saving

modes

Procedure to switch

modes

Conditions to enter into

the mode Status of equipment Conditions to recover

from the mode

Automatic

Energy Save

mode

When a specied period of

time *1 has passed since the

last use of the equipment. —

“Saving energy - press

START button.” appears on

the touch panel.

When a button on the

control panel *2 is pressed

or when print data or fax

data are received.

Sleep mode

When the [ENERGY SAVER]

button *3 is pressed or

when a specied period of

time *4 has passed since the

last use of the equipment.

When a particular option *5

is installed or when a

particular protocol *6 is

enabled.

The touch panel display

goes o and the [ENERGY

SAVER] button lights in

green.

Same as the Automatic

Energy Save mode.

Super Sleep

mode

When the [ENERGY SAVER]

button *3 or the [POWER]

button *7 is pressed or

when a specied period of

time *4 has passed since the

last use of the equipment.

When a particular option *5

is not installed and also

when a particular protocol

*6 is disabled.

Only the MAIN POWER

lamp (red) lights.

When the [POWER] button

is pressed, when print or

fax data are received

through a wired LAN or

when the time set for

Scheduled Print has come.

*1 The default value set at the factory shipment is 1 minute.

*2 Any of the [START], [ENERGY SAVER], [COPY], [e-FILING], [SCAN], [PRINT] and [FAX] buttons.

*3 [ENERGY SAVER] button on the control panel.

*4 The default value set at the factory shipment is 1 minute (The default value set at the factory shipment of the European version is 10 minutes).

*5 Any of the Wireless LAN Module, Bluetooth Module and e-BRIDGE ID Gate.

*6 Any of IPX, AppleTalk and other protocols. When the IPsec function is enabled, the equipment enters into the Sleep mode. For details, refer to the

following guide:

& TopAccess Guide (PDF): “Chapter 8: [Administration] Tab Page” - “[Setup] Item list”

*7 Even if you press the [Power] button, the equipment may not enter into the Super Sleep mode and the power may be turned OFF, depending on the

state of the equipment. For the conditions under which the equipment enters into the Super Sleep mode, refer to the following guide:

& TopAccess Guide (PDF): “Chapter 8: [Administration] Tab Page” - “[Setup] Item list”

For changing the set period of time for entering into each mode, refer to the following guide:

& MFP Management Guide (PDF): “Chapter 2: SETTING ITEMS (ADMIN)” - “Setting General Functions”

When the set period of time for switching to the Automatic Energy Save mode is the same as that for the Sleep mode or

the Super Sleep mode, the equipment enters into the Sleep mode or the Super Sleep mode after the set period of time.

For the European version

Contact your service representative to change the default settings noted above.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba e-studio 4540C Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba e-studio 4540C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info