Bedienungsanleitung Toshiba e-STUDIO 525P (Seite 5 von 346) (Englisch)

804434

Zoom out

Zoom in

Vorherige Seite

1/346

Nächste Seite

Safety information

Connect the power cord directly to an appropriately rated and properly grounded electrical outlet that is near the

product and easily accessible.

CAUTION—POTENTIAL INJURY: Do not use this product with extension cords, multioutlet power strips,

multioutlet extenders, or other types of surge or UPS devices. The power rating capacity of these types of

accessories can be easily overloaded by a laser printer and may result in poor printer performance, property

damage, or potential fire.

Do not place or use this product near water or wet locations.

CAUTION—POTENTIAL INJURY: This product uses a laser. Use of controls or adjustments or performance of

procedures other than those specified herein may result in hazardous radiation exposure.

This product uses a printing process that heats the print media, and the heat may cause the media to release emissions.

You must understand the section in your operating instructions that discusses the guidelines for selecting print media

to avoid the possibility of harmful emissions.

CAUTION—POTENTIAL INJURY: The lithium battery in this product is not intended to be replaced. There is a

danger of explosion if a lithium battery is incorrectly replaced. Do not recharge, disassemble, or incinerate a

lithium battery. Discard used lithium batteries according to the manufacturer's instructions and local

regulations.

CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the risk of injury from a hot

component, allow the surface to cool before touching.

CAUTION—POTENTIAL INJURY: To reduce the risk of equipment instability, load each tray separately. Keep all

other trays closed until needed.

CAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg (40 lb) and requires two or more

trained personnel to lift it safely.

CAUTION—POTENTIAL INJURY: Before moving the printer, follow these guidelines to avoid personal injury or

printer damage:

•Turn off the printer, and then unplug the power cord from the electrical outlet.

•Disconnect all cords and cables from the printer.

•If two or more optional finishers are installed, then remove the finishers individually from the printer.

Notes:

–Make sure to remove the topmost finisher first.

–To remove the finisher, hold the finisher on both sides, and then lift the latches to unlock the finisher.

•If the printer does not have a caster base but is configured with optional trays, then remove the trays.

Note: Slide the latch on the right side of the optional tray toward the front of the tray until it clicks into place.

•Use the handholds located on both sides of the printer to lift it.

•Make sure your fingers are not under the printer when you set it down.

•Make sure there is adequate clearance around the printer.

•Use only the power cord provided with this product or the manufacturer's authorized replacement.

Safety information 5

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba e-STUDIO 525P Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba e-STUDIO 525P

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info