Bedienungsanleitung Toshiba hd-ep 10 ktetm (Seite 21 von 72) (Englisch)

137365

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Introduction Connections

Playback

(Basic)

Playback

(Advanced)

Others

Chapter

Connections

Internet

connection

Step

HDMI stands for High Deﬁnition Multimedia Interface. HDMI transfers digital audio and uncompressed digital

video on a single cable. As a result, audio cables and video cables don’t need to be connected separately to

a device.

Connect the player to your TV.

HDMI INPUT

Depending on the equipment

connected to this player, such

as a TV or a projector, no sound

may be output by the display.

In this case, set “Digital Out HDMI”

( page 53) to “PCM”. If sound still

is not heard, use analog output.

HDMI cable (supplied)

Finally connect the supplied

power cord to a wall outlet.

To HDMI OUTPUT

This player supports simultaneous output of video on its HDMI and component video ports. However, some discs may

restrict output of video on the component video ports when viewing high deﬁ nition content or up-converted DVD content.

The resolution on the HDMI output will be the same as the resolution output on the component video output. Thus,

because the HDMI output can change automatically to match the maximum available resolution of your display, if you

connect both the HDMI output and component output, the resolution on the component output will change if the HDMI

output auto-adjusts.

HDMI, the HDMI logo and High-Deﬁnition Multimedia

Interface are trademarks or registered trademarks of HDMI

Licensing LLC.

After completing the connection, proceed to page 23 to make the setting.

Notes

• Refer to the owner’s manual for the TV to be connected to this player for more information concerning HDMI connections.

• When the HDMI connection is not veriﬁed, an error message appears on the front panel display. In this case, disconnect the

HDMI cable then connect it again, or turn off the connected HDMI device then turn it on.

• HDMI output is digital only, DVI analog is not supported.

• HDMI is an evolving technology, so it is possible that some devices may not operate properly with this player.

• To get the most possible beneﬁ t from Dolby Digital Plus, you should connect your HD DVD player to your AV receiver using

its HDMI input. If your AV receiver has this type of input, make sure it is connected to your HD DVD player and that the input

is set to use audio from HDMI (and not the SPDIF coaxial or optical input). If your AV receiver does not have an HDMI input,

then the next best choice is to use the SPDIF (coaxial or optical) input on your AV receiver.

• If you use the SPDIF optical output or analog outputs to connect your audio system and have the “Digital Out HDMI” (

page

53) set to “Auto” or “PCM”, the audio output level from these jacks will be reduced when listening to a multi-channel disc. To

restore the audio output level, set “Digital Out HDMI” to “Downmixed PCM”.

Via HDMI input

HD-EP10_02_E 21HD-EP10_02_E 21 07.3.20 11:21:18 PM07.3.20 11:21:18 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba hd-ep 10 ktetm Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info