497489
26
Zoom out
Zoom in
Vorherige Seite
1/59
Nächste Seite
26
8-4-3. Wiring Connection
WARNING
To plug the cable in the plug receptacle, take the
following precaution.
THIS APPLIANCE MUST BE EARTHED.
IMPORTANT
THE WIRES IN THIS MAINS LEAD ARE COLORED
IN ACCORDANCE WITH THE FOLLOWING CODE:
Place your finger on the lower part and push up
to open the screw cap.
(1) Open the screw caps and remove the two screws
securing the front cabinet.
(2) Close the screw caps as behind.
(3) Open the vertical airflow louver horizontally by
hand.
(4) Slightly open the lower part of the front cabinet
then pull the upper part of the front cabinet
toward you to remove it from the rear plate.
Fig. 8-4-6
How to open the screw cap
3
2
2
1
1
4
4
Vertical air flow louver.
Fig. 8-4-5
As the colors of the flexible cord of this appliance
may not correspond with the colored markings, to
identify terminals in your plug, as follows:
Connect BROWN colored core to plug terminal
marked letter L.
Connect BLUE colored core to plug terminal marked
letter N.
Connect GREEN AND YELLOW colored core to plug
terminal marked Earth Symbol
.
The installation of the cables has to be done in such
a way that the basic insulated wires for the infrared
sensor can not be touched.
<How to remove the front cabinet>
L
N
L
N
-LIVE
-NEUTRAL
-EARTH
: Brown
: Blue
: Green and Yow
Taking out the power cord
Cut off the slitted portion in the side face of the
rear panel to take out the power cord. After
this, remove burrs, sharp edges, etc., to
smooth the cut face..
<How to connect the power cord>
(For RAS-07YK-E, RAS-07YK-ES, RAS-10YK-E,
RAS-10YK-ES
only)
For the air conditioner that has no power cord,
connect a power cord to it as mentioned below.
After removing the front cabinet, remove the
terminal cover and the cord clamp.
Connect and secure the power supply cord and
secure the cord clamp and the terminal cover.
Cut the rear panel following the cutting mark and
put the power supply cord through the notch.
Be sure to smooth out the notch with a file, etc.
Slitted portion
Cord clamp
Terminal cover
Screw
Power supply
cord
Terminal block
Earth line
Screw
Screw
L
N
Fig. 8-4-7
<Stripping length of power cord>
NOTE :
Use standard wire only.
Wire type: More than H05-RN-F
Fig. 8-4-8
Earth line
40mm
10mm
10mm
30mm
L
N
26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Toshiba RAS-07YK-E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info