497489
31
Zoom out
Zoom in
Vorherige Seite
1/59
Nächste Seite
31
VP
Outdoor unit
Charge
hose (B)
Service port
Packed
valve
A
B
C
D
Gas
(Ø9,52)
Liquid
(Ø6,35)
Indoor unit
Lo Hi
High pressure
side handle
Pressure gage
Manifold valve
Low pressure side handle
Charge hose (A)
Fig. 8-5-5
CAUTION
KEEP IMPORTANT 4 POINTS FOR
INSTALLATION (PIPING WORK)
(1) Take away dust and moisture (Inside of the
connecting pipes.)
(2) Tight connection (between pipes and unit)
(3) Evacuate the air in the connecting pipes using
VACUUM PUMP.
(4) Check gas leak (connected points)
<Packed Valve Handling Precautions>
Open the valve stem all the way out; so not try
to open it beyond the stopper.
Securely tighten the valve stem cap with the
wrench or like.
Valve stem cap tightening torque is as follows;
Gas pipes side (Ø9,52) : 30 ~ 42 Nm (3,0 ~ 4,2 kgfm)
Liquid pipe side (Ø6,35) : 16 ~ 18 Nm (1,6 ~ 1,8 kgfm)
Service port cap : 9 ~ 10 Nm (0,9 ~ 1,0 kgfm)
<A5 mm hexagon wrench is required.>
8-5-3. Wiring Connection
(1) Remove the electric parts cover from the outdoor
unit. (1 screw)
(2) Connect the connecting cable to the terminals as
identified with their respective matched numbers
on the terminal block of indoor and outdoor units.
(Strip the sheath of connecting cable with follow-
ing stripping length to and insert into the terminal
block.)
(3) When connect the connecting cable to outdoor
unit terminal, make a loop as shown in the
installation diagram of indoor and outdoor unit, to
prevent water coming in the outdoor unit.
(4) Insulate the unused cords (conductors) with
water coming in the outdoor unit. Process them
so that they do not touch any electrical or metal
parts.
<Stripping length of connecting cable>
60mm
1
12
10mm
10mm
50mm
Connecting
cable
Screw
Terminal block
Terminal
screw
Cord clamp
Earth line
2
Earth line
For a three conductor cable
Fig. 8-5-7
CAUTION
Wrong wiring connections may cause some
electrical parts to burn out.
Be sure to comply with local code on running
the wire from the indoor unit to outdoor unit.
(size of wire and wiring method etc.)
Every wire must be connected firmly.
NOTE :
Wipe type : More than H05 RN-F
5mm
Flare nut
Stopper
Wrench
Valve body
Valve stem
Service port cap
Service port
Valve stem cap
Note : Service port at Gas pipes valve only.
Fig. 8-5-6
31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Toshiba RAS-07YK-E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info